 | | Re: Help me convert this train program to use events (NQC)
|
|
(...) Wow! That's quite a long cable. Is this the right product? I only found it using Pitsco's search box; it's not listed in any LEGO section as far as I could tell. (URL) (...) My original setup's RCX is a 1.0 with the AC adapter. The rails are (...) (19 years ago, 28-Nov-05, to lugnet.robotics.rcx.nqc, FTX)
|
| |
| | RE: Help me convert this train program to use events (NQC)
|
|
Brian Davis wrote..... ...... Worse yet, when the power runs low the RCX is likely to corrupt the firmware unless you put in code to monitor the battery level (something I'd suggest if you go this route). Standard Lego firmware is designed to detect (...) (19 years ago, 28-Nov-05, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Help me convert this train program to use events (NQC)
|
|
(...) For future, LEGO's educational division does sell 3m LEGO wires. (...) A 1.0 RCX that allows you to power the setup from an outlet is ideal for this. If it ends up being battery-based, you will have to adjust the power level as the batteries (...) (19 years ago, 28-Nov-05, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Help me convert this train program to use events (NQC)
|
|
(...) I wanted the layout to be pure LEGO, but if I run out of time building this I'll break down and use non-LEGO wire and my original setup. (...) I wasn't worried about hiding the RCX, but I have seen the batteries run down very quickly. In the (...) (19 years ago, 28-Nov-05, to lugnet.robotics.rcx.nqc, FTX)
|
| |
| | Re: Help me convert this train program to use events (NQC)
|
|
(...) That was basically my plan if I couldn't get the light sensors to work reliably. Based on Brian's post I might go back to my original design, though. (19 years ago, 28-Nov-05, to lugnet.robotics.rcx.nqc, FTX)
|
| |
| | Re: Help me convert this train program to use events (NQC)
|
|
(...) Speaker wire and small alligator clips will make a dandy solution for extending the basic wires - after all, you really only need one very long wire here (to the "remote station"), and yoiu have a working set-up. (...) Have you built and (...) (19 years ago, 28-Nov-05, to lugnet.robotics.rcx.nqc, FTX)
|
| |
| | Re: Help me convert this train program to use events (NQC)
|
|
(...) If the rcx is on the train why not mount touch sensors on the underside looking down. You could then attach small ramps to the track which would trigger the sensor. If you put the sensors on a spring loaded mounting you shouldn't have problems (...) (19 years ago, 28-Nov-05, to lugnet.robotics.rcx.nqc, FTX)
|
| |
| | Help me convert this train program to use events (NQC)
|
|
For Christmas I'm setting up a LEGO train on top of a narrow wall, so it has to operate like a shuttle -- stop at each end and reverse motor direction. My first attempt had a train regulator attached to a polarity switch, with the switch being (...) (19 years ago, 28-Nov-05, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.nqc, lugnet.trains, FTX)
|
| |
| | Re: compiling problem
|
|
(...) I'm glad that your problem was so quickly resolved. Isn't LUGNET great? In the future, if you have problems compiling NQC code you might want to post the exact error text generated by the compiler. If you use BricxCC to run NQC the full error (...) (19 years ago, 21-Oct-05, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: compiling problem
|
|
thanks for the advice rob, it compiled successfully (19 years ago, 21-Oct-05, to lugnet.robotics.rcx.nqc)
|
