 | | Re: maximum current of outputs
|
|
(...) 9.3x volts when a Train Power supply is used. Down to as little as 6.5 volts when batteries are getting pretty low. Dean -- -Dean Husby LUGNET Member #320 Co-Founding Member: VLC (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: SetWatch() only accepts constants
|
|
(...) You can use the NQC -watch now command to set the time. Dean (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Help needed for an NQC newbie
|
|
Hi, Normally you can see me in .space, .loc.ca, or org.ca and the like. But now that I have an RCX I want to program a bit. I have written my first NQC program and compiled it using RCXCC. I then downloaded it to my RCX but when I press run the legs (...) (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | RE: SetWatch() is remembered?
|
|
Take the batteries out (and unplug the external power on RIS 1.0) and it forgets everything, Date, Time, Programs/Tasks, even "Firmware"... "ZZZzzzombie" RCX :) mc. (...) (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | SetWatch() is remembered?
|
|
So does this mean that the RCX acts like a PC in that it does not forget the date/time when it is turned off or the batteries changed? Should I just write a one line program to set the time, and remove the time code from my actual NQC program? Thank (...) (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | maximum current of outputs
|
|
Hi hardware-specialists, does anyone know the maximum continuous current that a RCX motor output can drive? (I want to connect a light.) Thanks a lot. Bernd (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | RE: SetWatch() only accepts constants
|
|
Instead of sending ByteCodes from the PC and getting the RCX to interpret them, you can construct and send the SetWatch() OpCode plus the correct "constant" time and send it through Spirit.OCX (or directly, depending of the platform). (...) (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | SetWatch() only accepts constants
|
|
I just wrote a task and function that cause the RCX to receive data from the PC and then set the time on the RCX using SetWatch(). Unfortunately, I didn't realize that SetWatch() only accepts constants. NQC complained when integer variables were (...) (23 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
| | MIDI to NQC/RIS2.0 translator "Midi2LSC"
|
|
Hi, All ! I wrote a Windows 95/98/Me/2000 free software. This program named "Midi2Lsc" is SMF (Standard MIDI File) to LSC (LEGO Script Language of RIS2.0 SDK) and/or NQC translator. It is alpha test release status now. SMF format 0/1/2 support (...) (23 years ago, 28-Jul-01, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.nqc)
|
| |
| | Display the value of Scout sensors
|
|
Scout is cheaper, but when you debug NQC program in Scout, you have no way to watch the value of its sensors, I made a small program that can show sensors value in a RCX LCD, you can use remote to change watching sensor, message 1 for sensor1, (...) (23 years ago, 26-Jul-01, to lugnet.robotics.rcx.nqc, lugnet.robotics.scout)
|
