 | | Re: How to read the touch sensors on the Scout in NQC?
|
|
I was using my scout this past weekend as a coinbox detector to launch a mono rail. The touch sensors work exactly as Dave suggests. You can also just do the following: until(SENSOR_1); Waits until it's touched. until(!SENSOR_1); Waits until the (...) (23 years ago, 17-Dec-01, to lugnet.robotics.rcx.nqc, lugnet.robotics.scout)
|
| |
| | Re: How to read the touch sensors on the Scout in NQC?
|
|
(...) That is what I thought, but it will determine if the touch sensor is pressed. (...) Dunno, I'll try. Then again, if !=255 works... (...) If it were not for Perl I'd never write a line of code ^_^ (23 years ago, 17-Dec-01, to lugnet.robotics.rcx.nqc, lugnet.robotics.scout)
|
| |
| | Re: How to read the touch sensors on the Scout in NQC?
|
|
This program turns on motor A and leaves it running until a touch sensor attached to input 1 is pressed, then it turns off the motor and plays a sound: task main() { On(OUT_A); until(SENSOR_1 == 1); Off(OUT_A); PlaySound(SOUND_UP); } Dave (...) (23 years ago, 16-Dec-01, to lugnet.robotics.rcx.nqc, lugnet.robotics.scout)
|
| |
| | Re: How to read the touch sensors on the Scout in NQC?
|
|
Hi Chris, (...) this is a bit crazy, unless your sensor value is a bit pattern. (...) This is sensible, but are you sure it's ok to use equality and not inequalities like SensorValueRaw(1) < 240? (...) but it's equivalent, also in C, where & is (...) (23 years ago, 16-Dec-01, to lugnet.robotics.rcx.nqc, lugnet.robotics.scout)
|
| |
| | Re: How to read the touch sensors on the Scout in NQC?
|
|
I've sort of solved my problem, but not in a way which really makes total sense. Both of the below fragments work as expectd: #1 if ((SensorValueRaw(1) & SensorValueRaw(0)) != 255) #2 if ((SensorValueRaw(1) != 255) || (SensorValueRaw(0) != 255)) (...) (23 years ago, 16-Dec-01, to lugnet.robotics.rcx.nqc, lugnet.robotics.scout)
|
| |
| | How to read the touch sensors on the Scout in NQC?
|
|
All, I'm feeling pretty stupid right about now. I've read the NQC docs, looked in the newsgroups, books, etc, but I can't seem to figure out how to read the touch sensors on my Scout. I want to implement a bumper checking task but no matter how I (...) (23 years ago, 16-Dec-01, to lugnet.robotics.rcx.nqc, lugnet.robotics.scout)
|
| |
| | Re: MIDI to NQC/RIS2.0 translator "Midi2LSC"
|
|
Makino-san, I'm gald you did this because you just saved me the trouble of doing it myself!!! Thanks, Chris Barker (...) (23 years ago, 16-Dec-01, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.nqc)
|
| |
| | Re: Trigonometry and NQC
|
|
Thank you for these posts! This idea of creating a table of arctangents is just what I need. I'll let everyone know how it works after I redesign the racer. (The prototype, designed for speed, experienced a significant mechanical shock when it (...) (23 years ago, 14-Dec-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Trigonometry and NQC
|
|
Hi Richard, No, NQC does not implement any of the trig functions. However, you can do it yourself. The idea is to use a second order polynomial to approximate the sine function. You can get pretty good accuracy (within about 5%) if you break up the (...) (23 years ago, 12-Dec-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Trigonometry and NQC
|
|
(...) Hi Rich, Have a look at (URL) where you can find various tips around trig-functions under the restriction of integer values. Claude (23 years ago, 13-Dec-01, to lugnet.robotics.rcx.nqc)
|
