 | | Re: Respondre el missatge: LNPd problems
|
|
(...) ... (...) ... I uncommented that and recompiled, but nothing different happened. (20 years ago, 10-Oct-04, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Getting started; FFT; millisecond timing
|
|
(...) Thanks, Patrick. I just took the plunge into pbForth and I was stuck. After downloading the firmware, I couldn't get Ralph's console nor Hyperterminal to give me an "OK" response. I couldn't figure out how to get to the Bricxcc pbForth (...) (20 years ago, 10-Oct-04, to lugnet.robotics.rcx.pbforth)
|
| |
| | Respondre el missatge: LNPd problems
|
|
I also had a problem with lnpd and solved it. In my case was a problem with the configuration of the serial protocol, but the simptomes seemed like yours, thats I could receive from RCX but not send. I solved it modifiing the file rcxtty.c (or (...) (20 years ago, 8-Oct-04, to lugnet.robotics.rcx.legos)
|
| |
| | Re: LNPd problems
|
|
Can anybody help? If not I'll have to think of an alternative :s (20 years ago, 6-Oct-04, to lugnet.robotics.rcx.legos)
|
| |
| | Re: compiling problmes 2
|
|
(...) I had the same problem when going to newer binutils and gcc. Look at the patch brickos-gcc33.diff at (URL) first part of that patch changes the linker script slightly to avoid this error. (...) I think with the default linker-script the (...) (20 years ago, 7-Oct-04, to lugnet.robotics.rcx.legos)
|
| |
| | Re: compiling problmes 2
|
|
(...) Hello Jochen, hello everybody, thank you very much. Both of your hints helped a lot. As it were 271 linker-errors before your help, there are just 40 left now. Maybe someone can help me and tell me where the other references are defined and (...) (20 years ago, 7-Oct-04, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Bricx NQC
|
|
(...) I'm having a hard time parsing your english. I know that's not your fault, but it is making it harder to help you. The simplest way you can send a message to the RCX and have a program running on the RCX respond to that message is to use the (...) (20 years ago, 4-Oct-04, to lugnet.robotics.rcx)
|
| |
| | Motor power levels, floats and the LCD
|
|
Hi We just started using RCX and Robolab for a university course in cognitive systems. Our first lab was to navigate a maze using no sensors (internal representation only). The worst problem is inconsistent results given consistent power to the (...) (20 years ago, 3-Oct-04, to lugnet.robotics.rcx.robolab, FTX)
|
| |
| | LNPd problems
|
|
I'm having problems with using LNP to transmit to the RCX. I wrote a test program both on the RCX and the PC. Whenever the PC program tries to transmit data, I get the following error: lnp_integrity_write(): Interrupted system call What does this (...) (20 years ago, 2-Oct-04, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Bricx NQC
|
|
I want to send a message whon is formed for three numbers corespondente the information of the program than I'll create. I received an e-mail from "bricx" whon said: "BricxCC can accept some DDE messages. It can also act as an out-of-process COM (...) (20 years ago, 1-Oct-04, to lugnet.robotics.rcx)
|
