 | | Re: RCX low battery indicator problem
|
|
(...) I've tried the RCX2 firmware (firm0328.lgo). Same results: after downloading the firmware the RCX beeps (low battery signal) and is locked. In BrickOS when I read the battery sensor and write it's value on the display it says 620 (mV, Ithink) (...) (21 years ago, 5-Jan-04, to lugnet.robotics.rcx)
|
| |
| | Re: The BrickOS Task Manager
|
|
tid_t -> thread ID pid_t -> process ID ? "nanobapt" <nanobapt@wanadoo.fr> wrote in message news:3FF95FD4.608020...adoo.fr... (...) (21 years ago, 5-Jan-04, to lugnet.robotics.rcx.legos)
|
| |
| | Re: New Robolab user saying hello!
|
|
In lugnet.robotics.rcx.robolab, Paul Britton wrote: <snip> I am an electronics test development engineer for satellite payloads and (...) <snip> Paul, you must have seen my 'Satellite Tracker'. If not, go to (URL) and navigate to that project. (...) (21 years ago, 5-Jan-04, to lugnet.robotics.rcx.robolab)
|
| |
| | Sensor Power
|
|
ok, I have a real question. I'm interested in sending messages between RCXs using only the sensor ports. I've tested and found by switching between active and passive, signals can be sent, however, when the port is set to active, it is not powered (...) (21 years ago, 5-Jan-04, to lugnet.robotics.rcx.legos)
|
| |
| | Motor Display
|
|
For some silly reason, I was browsing through the BrickOS code and I noticed this: void motor_a_dir(MotorDirection dir) { dm_a.dir = dm_a_pattern[dir]; dlcd_hide(LCD_A_LEFT); dlcd_hide(LCD_A_RIGHT); if (dir == fwd || dir == brake) (...) (21 years ago, 5-Jan-04, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Does RIS2.0 set use the fiber optics cable?
|
|
"Luke W" <lwenke@dont_spam_me...tmail.com> wrote in message news:Hr03BI.1Bsz@lugnet.com... (...) Look right. I can't find any use for it in the instructions either. (...) of (...) In my RIS 2.0 set it is actually 25L (25 studs) long. What is the (...) (21 years ago, 5-Jan-04, to lugnet.robotics.rcx)
|
| |
| | Re: The BrickOS Task Manager
|
|
(...) only as a side note: you shouldn't really do this. you are burning precious cpu-cycles here. it should look something like while(!(rowdone && coldone)) msleep(5); if you're in a hurry you can make smaller msleep's... (21 years ago, 5-Jan-04, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Does RIS2.0 set use the fiber optics cable?
|
|
(...) USB tower is in the in the mindstorms ! And other functionnalities can be found ! Light transmission is something usefull in some way (...) Ask to LEGO :) nanobapt (21 years ago, 5-Jan-04, to lugnet.robotics.rcx)
|
| |
| | Re: Does RIS2.0 set use the fiber optics cable?
|
|
"nanobapt" <nanobapt@wanadoo.fr> wrote in message news:3FF961FA.404050...adoo.fr... (...) set, (...) of (...) Hi, Thanks for that reply. If the fiber optics cable in the spybotics set have an identical length to the RIS2.0 one then it seems Peeron's (...) (21 years ago, 5-Jan-04, to lugnet.robotics.rcx)
|
| |
| | Re: Does RIS2.0 set use the fiber optics cable?
|
|
(...) There are some way of reponse : - It's include in several box of spybotic - Lego says : *WDoes the Micro Scout read IR transmissions?* The Micro Scout reads LIGHT transmissions rather than Infrared (IR) transmissions. (in (URL) page) So (...) (21 years ago, 5-Jan-04, to lugnet.robotics.rcx)
|
