 | | Re: I'm passing the NQC torch...
|
|
(...) I wasn't sure where to post this. I want to reply to everyone's replies, but there are quite a few and I don't want to clutter things up, so I'm replying under my original post.... You're welcome! I really appreciate all of the thank-you's - (...) (21 years ago, 13-Nov-03, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Proximity Sensors for Legway
|
|
Hi Guys I have just updated the videos at (URL) It has balanced for several minutes on the kitchen floor in the mov00001 cofiguration.... but usually I start playing with the remote and that eventually throws it. I wasn't convinced before but I (...) (21 years ago, 12-Nov-03, to lugnet.robotics.rcx)
|
| |
| | Re: I'm passing the NQC torch...
|
|
Dear Dave, Thank you so much for your great contribution to the Mindstorms-community!!! Best regards, Dirk P.S.: John, all our hopes (trustfully) rely on you now! (21 years ago, 12-Nov-03, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Motors on Sensor ports
|
|
(...) Yeah... I wonder if that's a hardware limitation... (...) Well, that defeats the purpose... and I'm almost positive that powering a sensor port with 9v is a bad idea. (...) I dunno. Is it possible (I'm still in gr12 physics) that a circuit (...) (21 years ago, 12-Nov-03, to lugnet.robotics.rcx)
|
| |
| | Re: Motors on Sensor ports
|
|
(...) One thing you will find, is that you can't drive the motor backwards. Well, it won't go one direction. The direction depends on the wiring. Actually, that's just if you hook it to a motor port, AND a sensor port. I don't know how bad it is, (...) (21 years ago, 12-Nov-03, to lugnet.robotics.rcx)
|
| |
| | Re: I'm passing the NQC torch...
|
|
A few hours after I was working with my brand new RIS kit, I knew the programming environment was too limited for my needs. Thanks God there was NQC out there, very young but already very solid, offering an entire new world of possibilities. Without (...) (21 years ago, 12-Nov-03, to lugnet.robotics.rcx.nqc)
|
| |
| | Motors on Sensor ports
|
|
I'm just curious if there's any harm in connecting motors to active sensor ports... I know you don't get very much voltage/speed/torque, but you do get interesting readings that can be used to detect when the motor stalls. This is potentially a very (...) (21 years ago, 12-Nov-03, to lugnet.robotics.rcx)
|
| |
| | Re: Help w/install _or_ It all went so well
|
|
(...) [...] (...) Well it looks like the gcc-version-problem I had. The gcc >=3.x do not allow multiline strins without "\" anymore, which are still uses in brickos. So my hint is to install a gcc 2.95 and everything should work fine... Note: This (...) (21 years ago, 12-Nov-03, to lugnet.robotics.rcx.legos)
|
| |
| | Help w/install _or_ It all went so well
|
|
_warning_ I'm new to BrickOS, so be patient. I've just attempted to install using the instructions at (URL) went fine until step 4 command './configure; make' which looked like this: ... $ ./configure; make Welcome to the brickOS Makefile (...) (21 years ago, 12-Nov-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: I'm passing the NQC torch...
|
|
Dear Dave, All I can Say is Thanks. But that says it all. JL (21 years ago, 11-Nov-03, to lugnet.robotics.rcx.nqc)
|
