 | | Re: How do I use WinLNP?
|
|
Tom, I'm struggling with WinLNP too. Tried to compile the LegoStudio prog in VC++6, but keeps hanging up. Don't think my old laptop is up to VC++6, or maybe I need the patch that is mentioned in other messages. In the meantime I have been using the (...) (23 years ago, 16-Nov-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Lego LED Lights for Debugging or Decoration
|
|
(...) Again, these 9V system Single bi-colour LED light bricks are available at eBay: (URL) (23 years ago, 16-Nov-01, to lugnet.robotics.rcx)
|
| |
| | Re: RcxCC (whoops, BricxCC) update
|
|
(...) [snippage] (...) files are no longer written to the directory in which BricxCC resides. They are written to the Windows temporary directory as reported by the operating system. Toolbars are greatly enhanced. They drag, they float, they dock to (...) (23 years ago, 15-Nov-01, to lugnet.robotics.rcx.nqc)
|
| |
| | How do I use WinLNP?
|
|
Hi, Is there any instructions on WinLNP out there besides the ones on the homepage. I am kind of confused by them. Also, can anyone direct me to RCX talker? I have heard it mentioned a few times and it sounds like it is all I need, however I cannot (...) (23 years ago, 15-Nov-01, to lugnet.robotics.rcx.legos)
|
| |
| | compile multiple source files
|
|
Hello i see this post: (URL) to compile multiple source files, but i don't understand the changes to take to do, i see two parts: Makefile Fragment and Makefile.user patch, but My "Makefile.user" look a little bit diferent. I'm running legOS-0.2.4 (...) (23 years ago, 15-Nov-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Still having problems with helloworld.c
|
|
Thanks John! I will see if that works.I had almost given up and Mike was helping me set up the whole thing again alongwith the USB patch. Regards, Rajendra (...) (23 years ago, 15-Nov-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Still having problems with helloworld.c
|
|
Hi, I had the same problem you did and traced it back to a faulty line in loader.c (which contains makelx's main()). In revision 1.3 and earlier of that file you can find the following toward the end of the file: if(argc-optind<3 || lx.text_size==0) (...) (23 years ago, 15-Nov-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Does RL2.5 have array support?
|
|
Miles: On the question of arrays. Yes, it turns out that RL 2.5 *does* have array support (although you'd never find this out from the documentation). The trick is to use the container-of-container VI, which you only get in the Modifiers palette in (...) (23 years ago, 14-Nov-01, to lugnet.robotics.rcx.robolab)
|
| |
| | Battery eliminator?
|
|
Hi, I was looking at a webpage about a battery eliminator for a 1.5 rcx. It had a transformer and a voltage regulator and some dowel lengths to fit into the battery compartment. Can someone give me the webpage(or something similar) for this, I can't (...) (23 years ago, 14-Nov-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Mindstroms 2.0 and NT
|
|
(...) I have installed it with no problem on Win2K. Do you have a full RIS 2.0 with the USB tower? If so, you are probably out of luck for NT. I've heard you can by the serial tower from pitsco-dacta, which should allow you to use NQC on NT fine. (23 years ago, 12-Nov-01, to lugnet.robotics.rcx)
|
