 | | RE: Ooops! NXT Software Comparison correction
|
|
(...) After tuning, NBC achieved 73K test cycles. It achieved these great results by setting the task "priority" to 200. Unfortunately, unless the NXT-G task scheduler has been rewritten, these results might be a little too high. A NXT-G task (or (...) (17 years ago, 6-Sep-07, to lugnet.robotics.nxt)
|
| |
| | RE: Ooops! NXT Software Comparison correction / I2C Messaging Speed
|
|
(...) Nobody cheated or is dishonest. Everyone who writes firmware for the NXT is well-intentioned "good" people. Let's not mislabel good modern programming practice -- i.e. hardware device drivers integrated into the low-level firmware -- as (...) (17 years ago, 6-Sep-07, to lugnet.robotics.nxt)
|
| |
| | Re: Ooops! NXT Software Comparison correction / I2C Messaging Speed
|
|
(...) I think I understand. In this case, the limiting factor is the US sensor itself, how fast it can ing and interprete a return. Or from my standpoint (a physicist), it's a fundemental limitation of the physics of sound, not a limitation that has (...) (17 years ago, 5-Sep-07, to lugnet.robotics.nxt)
|
| |
| | Re: US-Sensor I2C-address
|
|
(...) To my knowledge the LEGO Ultrasonic sensor does not support changing its I2C address. IIRC it is hard-coded to 0x02. I do not think it is ADPA-compliant. John Hansen (17 years ago, 5-Sep-07, to lugnet.robotics.nxt.nxthacking)
|
| |
| | Re: Ooops! NXT Software Comparison correction / I2C Messaging Speed
|
|
(...) The errors that occur are that the sensor does not properly report variable distances as it is positioned at varying distances from an obstacle. If you slow down the read rate then it works correctly (i.e., with a wait of ~15 ms between read (...) (17 years ago, 5-Sep-07, to lugnet.robotics.nxt)
|
| |
| | Re: pbLua GUI ???
|
|
(...) I forgot the screenshot ;-) (URL) me: which of the connected NXTs is real ? One of this NXTs is software only (pbLuaAPI). Bye Christian (17 years ago, 5-Sep-07, to lugnet.robotics.nxt)
|
| |
| | Re: pbLua GUI ???
|
|
(...) New Eclipse version EUROPA (3.3) with LuaEclipse, RSE Target Management, RXTX and pbLuaAPI works excellent with pbLua ! You have direct access to all serial connected NXTs (Bluetooth and USB) from the Eclipse Workbench. A perfect professional (...) (17 years ago, 5-Sep-07, to lugnet.robotics.nxt)
|
| |
| | Re: Ooops! NXT Software Comparison correction / I2C Messaging Speed
|
|
Hi Dick, (...) actually I2C runs at something close to 12kHz in the LEGO firmware (I forgot the exact value). Jürgen (17 years ago, 5-Sep-07, to lugnet.robotics.nxt)
|
| |
| | Electronics Prototyping with the LEGO NXT
|
|
Hi Folks, I've been exploring various ways to use the LEGO NXT in enhancing electronics through Robotics and I've just posted a short video on the subject matter at my blog (URL). I'll be writing an eZCIRCUITs application note on the construction (...) (17 years ago, 5-Sep-07, to lugnet.robotics.nxt)
|
| |
| | RE: Ooops! NXT Software Comparison correction / I2C Messaging Speed
|
|
(...) I wasn't aware of this firmware limitation. I could not duplicate it when using the ROBOTC firmware. I've done three different test runs of 500K messages each with perfect results each time. Each test run used a different sensor. The delay (...) (17 years ago, 5-Sep-07, to lugnet.robotics.nxt)
|
