 | | Re: Enhanced standard NXT firmware
|
|
... (...) Hi John, I just tried to load it and just tested the "Try-me" light sensor. It worked fine. Not so much help, but I can try some more another day. Good work. Rasmus (...) (18 years ago, 19-Mar-07, to lugnet.robotics.nxt.nxthacking, lugnet.robotics, lugnet.robotics.nxt)
|
| |
| | Battery Level NXT-G Block
|
|
I've posted a new NXT-G Block that reads the battery level from the UI module IOMAP. Can also be used as a sensor block to detect low power conditions. Details and download: (URL) Ziv NXTasy.org (18 years ago, 19-Mar-07, to lugnet.robotics.nxt)
|
| |
| | Last call for my New York City NXT Meet-Up
|
|
I have the LEGO MINDSTORMS NXT ROBOTICS SET and since I'm so "into it", my father and I were thinking we could start up a Lego MindStorms NXT Meet up group/club in New York City where we could meet once a month (or every other month), build, (...) (18 years ago, 18-Mar-07, to lugnet.robotics.nxt)
|
| |
| | Detecting stall and slip conditions in NXT-G
|
|
I published a new "sensor" NXT-G Block that monitors that actual power sent to the NXT servos. This is useful to detected both stall conditions as well as the move challenging slip conditions. Full description and download are here: (URL) Ziv (...) (18 years ago, 18-Mar-07, to lugnet.robotics.nxt)
|
| |
| | MinMax NXT-G Block
|
|
I've published a small NXT-G block that allows to find the minimal and maximal value of a varying input. Description and download are here: (URL) Ziv NXTasy.org (18 years ago, 18-Mar-07, to lugnet.robotics.nxt)
|
| |
| | Missing links?
|
|
Hi guys, Are there missing any links in the "stable" section (the one with the links to RobotC, pbLua NBC etc) to the left of the forum (most likely since I put them there...)? I don't know if all can edit it but otherwise you can probably write to (...) (18 years ago, 18-Mar-07, to lugnet.robotics.nxt.nxthacking)
|
| |
| | Re: Enhanced standard NXT firmware
|
|
(...) I would have liked to have one permanently, but it seems a little steep. Last summer I got a limited edition (32KB or something) along with the an AT91 evaluation board. (...) Perhaps Section 5.1 is useful: (URL) I just tried to post but it (...) (18 years ago, 17-Mar-07, to lugnet.robotics.nxt.nxthacking, lugnet.robotics, lugnet.robotics.nxt)
|
| |
| | Re: Enhanced standard NXT firmware
|
|
(...) It actually was not a very big deal. I was familiar with the firmware source code since I had looked at it quite a bit since it was released, trying to figure out how to get it to compile with GCC. All the RIC bug fixes were things I figured (...) (18 years ago, 17-Mar-07, to lugnet.robotics.nxt.nxthacking, lugnet.robotics, lugnet.robotics.nxt)
|
| |
| | Re: Enhanced standard NXT firmware
|
|
(...) <snipped description> Holy crap John! You've been really busy! For anyone poking around in this forum, I can say that what John has done is pretty significant. I have written my own firmware for the brick so I know how much work must have gone (...) (18 years ago, 17-Mar-07, to lugnet.robotics.nxt.nxthacking, lugnet.robotics, lugnet.robotics.nxt)
|
| |
| | Enhanced standard NXT firmware
|
|
Over the past couple days I have used the IAR Embedded Workbench to implement some enhancements and bug fixes for the standard NXT firmware. The bug fixes are as follows: 1. RIC drawing code incorrectly checked the size of the OP_LINE structure for (...) (18 years ago, 16-Mar-07, to lugnet.robotics.nxt.nxthacking, lugnet.robotics, lugnet.robotics.nxt)
|
