 | | Re: Slower serial connection
|
|
Does anyone know how to reduce the baud rate used by IC? (I'm running Mac version 3.1.) I'd like to replace the serial cable with an RF link, but keep the interactivity of IC. Incidentally, I've found that the Parallax RF stamps work quite well on (...) (25 years ago, 16-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Slower serial connection
|
|
Hi everyone! The RF tx/rx units shown on the page were from Ming Microsystems. They were rated for 1200 baud, but I've been able to transmit/receive slower using the Parallax Inc. RF boards, which were rated for 300 baud. For slower serial (...) (25 years ago, 16-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Slower serial connection
|
|
Try this web page: (URL) . It should have what you want. I have not tried it myself, but I do have the reciever/transmitter pair described on the page. (...) <excerpt><fontfamily...smaller>Is it possible to slow down the speed of the serial (...) (25 years ago, 16-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | IR sensor
|
|
Hi.. does anyone know how to interface GP1u58X or IS1u60 Sharp IR sensor with handboard ?? i've tired to hack the GP1u58X from digital to analog output and plug it into analog input of HB, but the result is not good.. is there any software which can (...) (25 years ago, 16-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Re: serial output
|
|
My transmitter module can accept upto 1200 baud. can i modify this driver to run at 1200baud. if possible how? i dont really understant assembly code. could you also point me to a book or manual which gives assembler commands. many thanks M Fazal (...) (25 years ago, 16-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Slower serial connection
|
|
Is it possible to slow down the speed of the serial interface on the Handyboard? I have just gotten hold of a couple of RF transmit/receive pairs, but they are only able to go up to about 1200 baud or so. I don't intend using IC over the link, just (...) (25 years ago, 16-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Re: serial output
|
|
you're not going to be able to generate accurate bit times using Interactive C -- it'd have to be an assembly language driver. use the 9600 baud output driver located at (URL) your message you said: (...) (25 years ago, 16-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | serial output
|
|
hi i want to send a byte as a series of bit to a transamitter module i am using. the FAQ says i can use the digital 9, or SPI port or TOC3. i can output to these ports. the first problem is getting the delay times between bits. if i use the msleep() (...) (25 years ago, 16-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Lcd displays for the Handyboard.
|
|
Folks, Now and then I see people searching for LCD displays for the HandyBoards. I just came across some at a local surplus store. I purchased extras, and I'm will part with a few. These are new Vikay 2x16 lcd's, in a sealed bag. How about $5.50ea (...) (25 years ago, 16-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | array of char in IC
|
|
Hi, I am using IC. In my program I have an array of char (char serial_get_buffer[256]) as a global variable. This variable is used in a function. I want that when ever this function is called the array should be initialized to NULL. I tried (...) (25 years ago, 14-Feb-00, to lugnet.robotics.handyboard)
|
