| | Re: stalled motor detection
|
|
Shaft encoders are hard to beat. If the wheels are commanded to turn and aren't, that's a good indication that something is screwy. Plus, if you're doing dead reckoning, you need them anyway so they are already there! Gary Livick (...) (25 years ago, 27-Oct-99, to lugnet.robotics.handyboard)
|
|
| | stalled motor detection
|
|
Hi all, I'm working on a dead reckoning 'bot. I'm not really interested in what the wheels are doing unless they're stalled. Anyone know any good tricks for monitoring the motor current, or should I go with shaft encoders anyway? Thanks! Paul (25 years ago, 27-Oct-99, to lugnet.robotics.handyboard)
|
|
| | Re: Sonar Sensor
|
|
Danny, The Polaroid 6500 is very common, and if you have the expansion board on your HB you have a built in connection. There are drivers on the MIT HandyBoard site. The units are available from Acroname and they also have a good fact sheet. (2 (...) (25 years ago, 27-Oct-99, to lugnet.robotics.handyboard)
|
|
| | Re: Sonar Sensor
|
|
(...) Yep, I've checked out about every page I've seen on this. I just haven't had the time to do it yet. :| As soon as our competition is over and classes settle down (maybe in 3 years :()) I will get a chance to experiment with it. When will you (...) (25 years ago, 27-Oct-99, to lugnet.robotics.handyboard)
|
|
| | Re: Sonar Sensor
|
|
Try the Polaroid sonar sensors available from (URL) HB site has the info on how to hook it up to the Handy Board including the IC drivers. The Polaroid sonar works very well! Good luck, kam (...) ===...=== Kam Leang University of Utah Department of (...) (25 years ago, 27-Oct-99, to lugnet.robotics.handyboard)
|
|
| | Sonar Sensor
|
|
I'm designing a robot detection/obstacle avoidance system. And I want to install some Sonar sensor. I'm wondering if anyone would know of any good sonar sensor that can easily be used with the HB and that give good results? Any info on this would be (...) (25 years ago, 27-Oct-99, to lugnet.robotics.handyboard)
|
|
| | GP2D05
|
|
Hi Anybody got the GP2DO5 IR module working with the Handyboard (without expansion board) using IC ? I always seem to get a Logic "1" from the detector even if there are no obstacles in front of the detector. Any hints will be greatly appreciated. (...) (25 years ago, 27-Oct-99, to lugnet.robotics.handyboard)
|
|
| | Re: Servo 16 pgm +SPI on HC11
|
|
I have to admit that I have not actually finished the project, work commitments meant that it was shelved for a while. The easiest way to communicate to the HC11 is to use the software from the HB website that allows you to use one of the pins on (...) (25 years ago, 27-Oct-99, to lugnet.robotics.handyboard)
|
|
| | Debugging
|
|
I am developing a course at SJSU using the handyboard as the microcontroller for a competition being held at the end of the semester. This new course have us build the handyboard from scratch and go through the debugging process. I have help some (...) (25 years ago, 27-Oct-99, to lugnet.robotics.handyboard)
|
|
| | Re: Expansion Board and Smooth PWM
|
|
Bill, after unzipping the files, copy all the downloaded drivers into your interactive C Libs directory. These drivers must reside in this directory (drive:\IC\Libs) in order for IC to load them at startup. You will be asked if you want to replace (...) (25 years ago, 27-Oct-99, to lugnet.robotics.handyboard)
|