 | | sony ir function
|
|
I would like to know why the sony ir_data() only display 8 bit number instead of the 12 or 13 bit IR message? Does the number represent data only instead of the address or device? Does anybody knows how I could make the handyboard display the (...) (25 years ago, 21-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Re: for loop stack overflow
|
|
owen, what's inside the loop. i don't see any probl with the for loop itself. fred In your message you said: (...) (25 years ago, 21-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Re: for loop stack overflow
|
|
Owen, IC integers are signed 16-bit values ... - Nick - (...) (25 years ago, 21-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Encoder IO board
|
|
Hi everybody I have an application where I need to read 4 encoders, I am looking for an accurate encoder reading IO board which can be connected to an IBM PC. I am also looking for the rotary encoders for that. Please if you can help me find the IO (...) (25 years ago, 21-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Please I need help!
|
|
(...) I saw a contributed design a while back (on the HB web site, I think) of a multiplexer for running multiple Polaroid transducers off of one Polaroid ranging module. It involved the use of a few transistors and such. The idea was to use extra (...) (25 years ago, 20-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | for loop stack overflow
|
|
THis may be a dumb question on my part, but we are getting stack overflows on for loops such as for(int i = 0;i<1000;i++){...} when using values over 100 or so. Is this an 8bit counter thing or something else? Thanks, Owen Popplestone (25 years ago, 20-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Handyboard low voltage motor control
|
|
Well, I went with separate h-bridge to maintain PWM and it turns out that even though the motors are geared down, they still don't have enough torque to haul around all the batteries. Looks like I'll stick with 9v motors... Thanks for the (...) (25 years ago, 20-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | RE: port addresses
|
|
This is the online ordering form for motorola literature (if you are looking for motorola manuals) (URL) Message----- From: SNESS@amcomp.com [mailto:SNESS@amcomp.com] Sent: Wednesday, October 20, 1999 10:27 AM To: jimmn@xnet.com; (...) (25 years ago, 20-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | GLOBAL POSITIONING SYSTEM
|
|
I learned that somebody has successfully connected GARMIN GPS to HB. If I am not wrong , this GPS is not be able to receive any signal in building. If this the case, GPS is only good for outdoor robotics. Another thing is about the accuracy of the (...) (25 years ago, 20-Oct-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Vector 2x
|
|
I know everyboard has been sucessfully connected vector 2x to hb. I try to do the same thing as per Tom Brusehaver guides. Connecting as below :- +5V (SPI) to VCC (vector2x) GND(SPI) to GND (vector2x) MISO(SPI) to SDI (vector2x) MOSI(SPI) to (...) (25 years ago, 20-Oct-99, to lugnet.robotics.handyboard)
|
