 | | Downloading problems
|
|
Fred This is a followup to your answer regarding downloading problems 1. The 6811 Downloader does not seem to work with HB. I get mesaages varying from recieved 0, wanted 255-or serial port not responding. I am DL from a MAC PPC 6500 OS 8. 2. This (...) (26 years ago, 26-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | RE: servo motor
|
|
Since the System 3000 servos appear to be made by Futaba, and they specify a standard Futaba "J" connector, my guess is that they would plug right in. Futaba practice is as you state: red=5V, black=common, white=signal. Brett Anthony -----Original (...) (26 years ago, 26-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: CHARGER BOARD PROBLEM(URGENT)
|
|
phillip, please go through the sequence of tests in the assembly directions (as if you were building the serial/charger board from scratch), and indicate the point at which you first detect a problem. (URL) your message you said: (...) (26 years ago, 26-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Downloading problems
|
|
Use 6811 Downloader to download pcode_hb.s19. Power cycle, and the Handy Board should beep and display a version message on its LCD screen. Then, run IC modem or IC printer depending on which port you are using. It should be configured to boot with (...) (26 years ago, 26-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Downloading problems
|
|
I assembled the HB board some 2.5 years ago. At that time it seemed to work very well. The hook is that I'm quite strong on the Hardware side and rather anemic with regard to software. In the earlier time I would download it from a Mac 11si-no (...) (26 years ago, 26-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Re: dc motor output control? Please help!
|
|
the short answer is that you can't use 3v motors with the handy board. the FAQ states this: (URL) you use the "separate motor power supply" hack, with a 6v battery, you might be able to get 3v motors to work. see (URL) your message you said: (...) (26 years ago, 25-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | CHARGER BOARD PROBLEM(URGENT)
|
|
hI FRed, anothony and others, I just plug in the RJ11 in the HD and charger board. It supposed that the red LED on the charger board should light up. It failed to light up. When I plug in the adaptor onto the charger board, the red LED light up but (...) (26 years ago, 25-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | Merry Christmas!
|
|
Merry christmas! Megan See you real soon, you rock my world! Justin thanks for the many rides to camp Erv Shine on you crazy diamond! Joel be careful! See you soon. Jeremy Don't work too hard, *laugh* Jacob See ya soon, take care. All my A-Rocket (...) (26 years ago, 25-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | dc motor output control? Please help!
|
|
hi everyone, i need some help on controling the output voltage of the dc motor ports. the o/p of the motor port is 12V. but my motor required voltage is only 3V. i like to know if there is any way to clamp down the voltage to 5V or lesser. i try (...) (26 years ago, 25-Dec-98, to lugnet.robotics.handyboard)
|
| |
| | servo motor
|
|
Hello again, I am using a Tower Hobbies System 3000 servo motor on my expansion board. Does anyone know if the black, red, and white wire match up with ground, 5 volts, and control respectively for that particular brand of servo motor? Scott Sherman (...) (26 years ago, 24-Dec-98, to lugnet.robotics.handyboard)
|
