To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.robotics.handyboardOpen lugnet.robotics.handyboard in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / Handy Board / *5014 (-10)
  Re: dc motor output control? Please help!
 
the short answer is that you can't use 3v motors with the handy board. the FAQ states this: (URL) you use the "separate motor power supply" hack, with a 6v battery, you might be able to get 3v motors to work. see (URL) your message you said: (...) (26 years ago, 25-Dec-98, to lugnet.robotics.handyboard)
 
  CHARGER BOARD PROBLEM(URGENT)
 
hI FRed, anothony and others, I just plug in the RJ11 in the HD and charger board. It supposed that the red LED on the charger board should light up. It failed to light up. When I plug in the adaptor onto the charger board, the red LED light up but (...) (26 years ago, 25-Dec-98, to lugnet.robotics.handyboard)
 
  Merry Christmas!
 
Merry christmas! Megan See you real soon, you rock my world! Justin thanks for the many rides to camp Erv Shine on you crazy diamond! Joel be careful! See you soon. Jeremy Don't work too hard, *laugh* Jacob See ya soon, take care. All my A-Rocket (...) (26 years ago, 25-Dec-98, to lugnet.robotics.handyboard)
 
  dc motor output control? Please help!
 
hi everyone, i need some help on controling the output voltage of the dc motor ports. the o/p of the motor port is 12V. but my motor required voltage is only 3V. i like to know if there is any way to clamp down the voltage to 5V or lesser. i try (...) (26 years ago, 25-Dec-98, to lugnet.robotics.handyboard)
 
  servo motor
 
Hello again, I am using a Tower Hobbies System 3000 servo motor on my expansion board. Does anyone know if the black, red, and white wire match up with ground, 5 volts, and control respectively for that particular brand of servo motor? Scott Sherman (...) (26 years ago, 24-Dec-98, to lugnet.robotics.handyboard)
 
  Source of Handyboard in UK?
 
I have a small quantity of handyboard pcb's available for 16GBP the set, handyboard plus charger including the hard to find ZTX darlington. Post paid in UK, Visa and Mastercard accepted. This is a limited offer, once they are gone I will not be (...) (26 years ago, 24-Dec-98, to lugnet.robotics.handyboard)
 
  Happy Holidays
 
Happy Holidays For All !!! (26 years ago, 23-Dec-98, to lugnet.robotics.handyboard)
 
  RE: expansion board - servo control
 
I've had a similar problem, make sure your servo power is fully charged. An undercharged system will sometimes drive all the way one way. Mike Ross ---...--- From: shsc9801@condor.stcl...state.edu] Sent: Wednesday, December 23, 1998 8:04 AM To: (...) (26 years ago, 23-Dec-98, to lugnet.robotics.handyboard)
 
  serial ports question
 
hi, can i have 2 sets of serial communications at the same time with the handyboard? i have 1 set that is between the handyboard and the SSC via pa7. i want to have another channel, pc serial application to handyboard, in that one direction only, (...) (26 years ago, 23-Dec-98, to lugnet.robotics.handyboard)
 
  RE: encoder and motor questions
 
I am doing something very similar, but instead I am trying to follow a black line on a white background. Either way, I am using IR detectors and emitters. They are readily available and work very well. I'm sorry I have never used an encoder to know (...) (26 years ago, 23-Dec-98, to lugnet.robotics.handyboard)


Next Page:  5 more | 10 more | 20 more

Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR