|
|
 | | New user - printf question/problem
|
| Okay, this may seem silly, but I've got a very basic question. Just received a new handyboard (assembled, ready to go from Gleason). After charging it up, installing the pcode and booting all works fine. The 'Interactive C' text shows on the screen. (...) (26 years ago, 21-Nov-98, to lugnet.robotics.handyboard)
| | | | | Using 30VDC to drive motors
|
| Hello, I have finished building Matt Harlan's H-Bridge circuit (from the Handyboard FAQ) and I have come across the following instructions: "Make sure the supply ground for the 18200's is connected to the HB ground. You'll get some very strange (...) (26 years ago, 21-Nov-98, to lugnet.robotics.handyboard)
| | | | | Re: motor port problem
|
| (...) to make the connector more physically and electrically stable. (...) of course, only 2 connections are needed to make a ckt. (...) you should figure up to several amps of current flow. (...) it should work fine. good luck. fred (...) (26 years ago, 21-Nov-98, to lugnet.robotics.handyboard)
| | | | | Re: LEGO: looking for gears
|
| (...) Call 1-800-453-4652 for a Lego Shop-At-Home catalog. They have an assortment called #5229 Gears & Differentials for $4.50, that has all but the huge 40-tooth gears. Shipping is free. If you need the 40-tooth gears, you can get four of them (...) (26 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
| | | | | Re: motor port problem .
|
| Philip In a message dated 98-11-19 21:05:04 EST, you write: << hi, I have a big problem. I followed the method of yours that just lift up pin 8 of one L293 and wirewrapped it. The positive supply is wirewrapped to pin 8 . How about the negative (...) (26 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
| | | | | Re: Sharp IS1U60 availablity
|
| Check B. G. Micro 800-276-2206 www.bgmicro.com I would not be too concerned with the actual part number, just look for an Infared sensor or remote control sensor. Also get the pin outs as these may be different. Also have you considered using fewer (...) (26 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
| | | | | serial communication
|
| Hi, Does anyone know the what is the most suitable port settings to use ? The Bits per second, number of data bits and stop bits, parity bit and the flow control type. Thanks for helping... (26 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
| | | | | Compling *.ICB files
|
| Hello, Does anyone have any tips on compling *.ICB files on Windows NT? I have IC 3.2. Using the as11_ic.bat file works with much modifications to the the *.asm files. The web based complier at Newton Labs compiles the code, but loading the ICB file (...) (26 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
| | | | | arithmatic operation(more)
|
| Hi all; I have also reckon that following numbers are also giving 2 in answer if divided by same numbers. 5.1,6.1,7.1,4.6,5.6,....4,1.92.3, 2.8,3.3,3.8,8.2,8.7,...10.2,10.7, thanks javaid iqbal (26 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
| | | | | Arithmatic operation
|
| Hi all, I am dividing 4.1 by 4.1 in following manner and getting answer 2. instead of 1. Dividing 4.2 by 4.2 give 1 result, dividing 4.6 by 4.6 again give 2. Except 4.1 and 4.6 rest all numbers give 1 result. I am using IC 3.2. Any help in this (...) (26 years ago, 20-Nov-98, to lugnet.robotics.handyboard)
|
|
