|
|
 | | Re: General use PCB
|
| (...) Option #1: How about making some of your own? If you need 60, then the prices from board houses start getting pretty low. Check out these places: (URL) made up a small spreadsheet for expresspcb and apcircuits pricing, and at quantity 60 you (...) (26 years ago, 5-Aug-98, to lugnet.robotics.handyboard)
| | | | | digital out
|
| I am in the need for additional digital outputs. I have read the FAQ and found out that to get 8 more digital outs, I have to connect the 'hc374' clock line to any of the unused output latch selects of the 'hc138'. Has anyone done this? If so, any (...) (26 years ago, 5-Aug-98, to lugnet.robotics.handyboard)
| | | | | Pull Up Resistor
|
| Hi, The polaroid documentation mentions that a 4.7K resistor should be placed between ECHO and Vcc. Should this be done when interfacing to the HB? Thanks, Sheridan (26 years ago, 5-Aug-98, to lugnet.robotics.handyboard)
| | | | | Handy Board for Sale!
|
| To Anyone Interested, I have a nearly brand new complete Handy Board for Sale. I used it one week and unfortunately it does not have the capability to do what I want. It is complete with battery installed, serial/charger board, software for IBM, (...) (26 years ago, 5-Aug-98, to lugnet.robotics.handyboard)
| | | | | General use PCB
|
| We have been using the Radio Shack, Archer board #276-162A. Specifications: Dimensions 3 inches x 4 inches, with copper lands on one side. 30 holes by 25 holes with mounting holes at 2.5 inch and 3.5 inch spacing. We have to told that Radio Shack (...) (26 years ago, 5-Aug-98, to lugnet.robotics.handyboard)
| | | | | Re: Pull Up Resistor
|
| (...) The sensor connectors on the HB already have pullup resistors on the signal inputs (as I recall they were 47K), so you shouldn't need to add an additional pullup. If you want to make sure, just check the signal connection with a voltmeter to (...) (26 years ago, 5-Aug-98, to lugnet.robotics.handyboard)
| | | | | yet another hb for sale
|
| One Handyboard, from Gleason Research, specifically GRHB-PC, with all cables, power supply, software, LCD, battery, charger board, etc. Get it with two Lego 9 volt gearmotors (they cost me $19 each) and my key for IC 3.2. Used for one small project, (...) (26 years ago, 5-Aug-98, to lugnet.robotics.handyboard)
| | | | | troubleshooting
|
| I am assembling my handyboard and am at the stage where i have completed the motor and analog circuits. When I test hte analog circuit the LCD screen prints"press START to test knob..." when i press start the board beeps and the screen goes blank. (...) (26 years ago, 5-Aug-98, to lugnet.robotics.handyboard)
| | | | | CW TECHNOLOGY
|
| ALL, Do you know if the guy from CW Technology who sells MiniBoard is still doing selling them. I sent him an email, but no reply so far. Thanx. Hachemi (26 years ago, 5-Aug-98, to lugnet.robotics.handyboard)
| | | | | mouse encoders
|
| hello, does anyone know how to interface the handyboard with a shaft encoder from a mouse? i am interested in using one out of a microsoft mouse, which uses electrical contacts, instead of an optical sensor. what kind of signal is sent from the (...) (26 years ago, 4-Aug-98, to lugnet.robotics.handyboard)
|
|
