 | | Re: Sumo-Robots
|
|
look at (URL) for th Dutch sumo-robotics Greetz Emiel ---...--- (...) (26 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: motor power problems
|
|
In a message dated 98-07-24 20:49:35 EDT, you write: << Has anyone had similar problems, and if so how did you solve them? I know there's a way to provide a separate power supply for the motors, but I'd rather not cut traces on the board except as a (...) (26 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Various Basic Issues
|
|
Howdy from Texas. I have set myself the goal of making a robot with the handyboard -- just for the learning of it. Until 2 days ago I had zero knowledge of electronics, although I am teaching myself using some kits and books. I also do not know C (...) (26 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: troubleshooting
|
|
ok, i finished the digital input circuit and the first time i turned it on both green and red lights stayed illuminated so i checked the orientation of all the chips and they were correct so i removed and reinserted them for good measure. This (...) (26 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: IR Emmiter and Detector for RW Pro
|
|
Hi ! You get a fantastic collection of datasheets and component specs at www.questlink.com regards..... Rajaraman. -----Original Message----- From: Javaid Iqbal <javaid@student.unsw.edu.au> To: Handy Board <handyboard@media.mit.edu> Date: Sunday, (...) (26 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | ELMO
|
|
Hello all, From December 1997 until now I've been working on my Master's project. It consisted of a theoretical part and a practical part. In the practical part I made a little mobile robot using a Handy Board. In the next couple of weeks I will be (...) (26 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | 68hc11F1
|
|
Hello all, Thanks for all the replies that you have send. My board is now working, at 16 mhz with flash and ram. Richard (26 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | RE: fischertechnik
|
|
First of all, the HandyBoard works fine with fischertechnik. I've been using fischertechnik for a variety of purposes since about 1980. I've also used Lego Technic, although less extensively, for ten years or so. Size/Scale: If you build identically (...) (26 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: troubleshooting
|
|
In your message you said: (...) good.... (...) yes, this is normal -- before you load pcode_hb.s19, the LCD is just as you describe. (...) d (...) I'm not clear the problem. if you enable "ignore feedback", does it then download properly? if so, (...) (26 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | troubleshooting
|
|
I have a problem assembleing my hanyboard. I am at the stage where i am doing the digital input circuit. Before this I successfully loaded pcode_hb.s19 into the handyboard and the interactive C message appeared. However, before i loaded pcode_hb.s19 (...) (26 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
|
