 | | Windows NT experiences?
|
|
Hi all, I was wondering if people would please "share" their experiences running Interactive C on Windows NT. Is anyone using the old freeware DOS IC on NT? Did you have any trouble getting it to work? Please send to the list, or me privately if (...) (26 years ago, 9-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Legos
|
|
the motor is available via LEGO Shop at Home (S@H for short) tel: 1-800-453-4652 there are three kind of motors: #5114 $17.50 (the one that you see in #8270, old style) #5225 $17.50 (the one that in #8735, newer one, with gear reduction) #5119 (...) (26 years ago, 9-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | Legos
|
|
I know someone just asked this question, but where can I buy just the lego motors, and not the $45.00 set from a toy store. Thanks, Mike ---...--- Mike Reiling macman@inreach.com University of the Pacific Student of Computer Science One tequila, two (...) (26 years ago, 9-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | Re: Include directive, HexMon
|
|
I had same problem, and found that if you put the include files in the same directory as your file to be complied, and then place the file in quotes (eg. #include "6811regs.asm") it will compile. John (...) (26 years ago, 9-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | Re: serial communications
|
|
Justin Here is the file. Please feel free to modify/improve. I'm a doctor not a programmer, and I better keep my day job. Notice it borrows Randy Sargent's and Dr. Richard F. Drushel's routines found in serialio.c and math.c, both on the handy board (...) (26 years ago, 9-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | clock signal needed for decoder chip
|
|
Hello, I am hooking some HP decoder chips to the handyboard. They are HCTL-2020's and they decode a motor position encoder signal. My problem is that I need to hook one of the pins on the 2020 (the CLK pin) to a clock. I'd like to get ahold of the E (...) (26 years ago, 8-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | Re: handshaking
|
|
(...) Regarding your earlier message, if you're just wanting to talk to a GPS, then you don't need handshaking, because I haven't found one yet that supports it. It is a simple three-wire interface to most GPS's, TX/RX and Ground. They don't support (...) (26 years ago, 8-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | Re: LCD Removal
|
|
All pcodes shipped with IC 3.1/3.2 are designed to work fine either with or without LCD. Prior to 3.1, you have to build a pcode specially to disable the LCD. -- Randy (...) (26 years ago, 8-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | Re: any micromice out there?
|
|
Hi Brian, Several of my Penn State Abington freshman and sophomore engineering students constructed a working micromouse from LEGO and a HB. The approach was a vehicle that can only move in the north-south or east-west directions by alternately (...) (26 years ago, 8-Jun-98, to lugnet.robotics.handyboard)
|
| |
| | handshaking
|
|
could you please explain to me the details of handshaking? i need to understand this before i can go any farther. exactly what is transponded during this? and how is this implemented thru assembly language? thank you. Justin D. Gullotta.. , (...) (26 years ago, 8-Jun-98, to lugnet.robotics.handyboard)
|
