 | | How to know my position??
|
|
Hello We are French Students and we are looking for a system to give the robot, which contains the Handy Board card, his position on a table (2*3m). Could you send us any information about this? Thank You... En français: Salut, Nous sommes des (...) (27 years ago, 20-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | How to know my position??
|
|
Hello We are French Students and we are looking for a system to give the robot, which contains the Handy Board card, his position on a table (2*3m). Could you send us any information about this? Thank You... En français: Salut, Nous sommes des (...) (27 years ago, 20-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | How To know my position??
|
|
Hello We are French Students and we are looking for a system to give the robot, which contains the Handy Board card, his position on a table (2*3m). Could you send us any information about this? Thank You... En français: Salut, Nous sommes des (...) (27 years ago, 20-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Error in FAQ
|
|
In your message you said: (...) whoops. it's fixed now. thanks. one thing: the range was correctly indicated in the FAQ as $6000-$6FFF. You've got it here as $6000-$6999. Fred (27 years ago, 20-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Error in FAQ
|
|
While looking through the FAq I noticed what I think is a mistake - could you check ? In the memory map it says: Expansion I/O Bank 2 $6000-$6999 Reads Enable Y3; writes enable Y5 surely this should read : reads enable Y4, writes enable Y5. Can you (...) (27 years ago, 20-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | unsubscribe
|
|
unsubscribe microp@geocities.com (27 years ago, 19-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | OOH YES! Its Trigonometry
|
|
I've looked up the formula for calculating the asin and ocos. They're enlosed as .GIF attachment, because I can't type then in ASCII, but I'm sure you can view it. I hope they'll be usefull to you. Jeroen vd. Vegt. PS. I hope you already knew that (...) (27 years ago, 19-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Re: TOC4INT interrupt
|
|
(...) Yes, 1 mSec. (...) Time slows down (the tick counter is no longer accurate), your motors get variations in their PWM signal, and you risk losing syncronization with any servos you have out holding position. (27 years ago, 19-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | TOC4INT interrupt
|
|
How do you know when you are "using too much resources" when installing programs into the system interrupt? Is there a limit to how long the system interrupt routine can last? What happens if all the instructions I place in there causes the whole (...) (27 years ago, 19-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | sensor for distance
|
|
(...) ***...*** * Frederic GIAMARCHI * * I.U.T. G.E.I.I. de NIMES * * 8, Rue Jules RAIMU * * 30907 NIMES CEDEX * * FRANCE * * Tel.: 04 66 62 85 22 * * Fax : 04 66 62 85 01 * * Email : giamarch@iutnimes.un...-montp2.fr * ***...*** (27 years ago, 18-Nov-97, to lugnet.robotics.handyboard)
|
