 | | MAgentic card readers again...
|
|
Anyone can help me about the way to connect a magnetc card reader to the handy? I use the idea from david negro , that use the SPI port, but i don't can make work the code... Can anyone tell me uf exists other source of that info ont the web?? (...) (27 years ago, 6-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: IR output on HB
|
|
No, don't use a transistor! The HB's IR out already has one. But the parallel-with-a-sepa...r-for-each method is correct. -Fred In your message you said: (...) (27 years ago, 5-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: IR output on HB
|
|
Run them in parallel, use a transistor. Like so: +5v | +---+---+---+---+---+ | | | | | | \ \ \ \ \ \ / R / R / R / R / R / R \ 1 \ 2 \ 3 \ 4 \ 5 \ 6 / / / / / / -- -- -- -- -- -- \/ \/ \/ \/ \/ \/ -- -- -- -- -- -- HB + | | | | | | \ | | | | | | / (...) (27 years ago, 5-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: CdS cells
|
|
[David.J.Dostal@lawrence.edu] spake unto the ether: (...) I just ordered some from Mouser, the smaller of the two physical sizes they have, 3K to 100K I believe are the light/dark resistances. These give analog(PORT) values of about 10 in ordinary (...) (27 years ago, 5-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | CdS cells
|
|
hi everyone, I am looking to purchase a batch of CdS photo cells but I think that I need more information before I order. The catalogs (Digi-Key, Mouser, etc.) list several different photocells (different resistances, power dissipation, etc.) and I (...) (27 years ago, 5-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | 3V motors
|
|
Mike, I had a similar problem and the solution is not to put a resistor in series with the motors. With the varying amount of current a motor draws, the voltage drop across the resistor will vary as well and the motors will not see a consistent 3V. (...) (27 years ago, 5-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | 3v motors
|
|
I have a cute little tracked robot base i want to run from a handyboard, but the problem is that it has 3V motors. The handyboard is set up to power 9v, right? The way i see it, i can either just put a resistor in series with the motor to drop the (...) (27 years ago, 5-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | IR output on HB
|
|
Hi, I'm trying to get the ir output on the handy board to power more than 4 LEDs (need to power 6), anything beyond that the ir signals become drastically weak. I have these LEDs wired serially. I'm not too familiar with electronics, so is it (...) (27 years ago, 5-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | Re: ? mobile base for handyboard
|
|
Depends on what you want to accomplish. The LegoBug can use otpical sensors to follow a black tape and the smaller 'micro-motors' are better (less play) than the standard 9v motors. check out (URL) for instructions, ordering info and a price list. (...) (27 years ago, 4-Aug-97, to lugnet.robotics.handyboard)
|
| |
| | ? mobile base for handyboard
|
|
Can anyone suggest mobile bases for the handyboard. I am looking for something which is reasonably priced and fairly easy to work with (for a "software" type!). Has anyone used the ARBE-ONE? LEGOBug? Thanks. David Naugler (27 years ago, 4-Aug-97, to lugnet.robotics.handyboard)
|
