 | | Interrupt driven serial
|
|
Anybody have any sample code for interrupt driven serial output. I need to send out 3 bytes and have the SCI interrupt occur after each byte. Thanks! -John (27 years ago, 10-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Dissecting a mouse for the Handyboard
|
|
I opened a mouse a while back. Although I was kinda young at that time, I believe what I saw was two incremental quadrature encoders (from what I remeber visually). One encoder is for the X axis and one for rhe Y axis. The mouse I opened had slotted (...) (27 years ago, 10-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | Programing prob.
|
|
Trying to figure out writing in 'C'. If anyone could help it would be great. I have included my code but it needs alot of work!! I am using the Handyboard w/ LEGObug and I can't figure out how to put the motors in a loop and also have the two touch (...) (27 years ago, 10-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | SONY-TX.ICB
|
|
Has anyone tried to use SONY-TX.ICB with any luck? I get the icb loaded just fine and can get it to trigger the ir output test led (the little red one) with nothing plugged into the connecter, but when I plug an ir led into the jack and run the (...) (27 years ago, 10-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Dissecting a mouse for the Handyboard
|
|
(...) (URL) at the "Loboto-Mouse (tm)" section on the first page. Cheers, Michael A. Tyborski WebWerx Milwaukee, WI (27 years ago, 10-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | Dissecting a mouse for the Handyboard
|
|
Hi All, Has anyone dissected a PC Mouse, and interfaced it with the Handyboard, to use it as a directional and speed indicator. Any information on how the mouse works or how it can be used with the handyboard would be appreciated. Thanks Michael (27 years ago, 10-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | RE: HBDL still not working with win95...
|
|
Try going to the shutdown menu for Win95. Select restart in Msdos mode. Once the system gives you the dos prompt, try hbdl again. (...) may take a min but how much speed do you need?... if that works... try 19200, 38700, blah blah blah... (...) (...) (27 years ago, 9-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | magnetic card devices
|
|
I need to read a magnetic card device from a Handy Board, and i don't know how this device send me the read data. Can anyone hel me about that??? Thanks for all . [sorry for my english . Me Tarzan , you Shane ... ;>) ] Germán Gentile. (...) (27 years ago, 9-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | Handy Board Weight
|
|
Hmm.. Seems my reply address was wrong in my original message, so i'm re-posting this with the right address. (Thanks Fred for pointing this out). I'm working with a robot where weight is very important. I was wondering if anyone had the exact (...) (27 years ago, 9-Jun-97, to lugnet.robotics.handyboard)
|
| |
| | Re: System Interrupts & frequency counting
|
|
(...) Paul, What you want to do is easy. All you need to do is get a small assembler routine which uses the Input Capture feature. Set the IC via registers to trigger when a rising pulse begins, it will stash the time and strigger an interrupt. Then (...) (27 years ago, 9-Jun-97, to lugnet.robotics.handyboard)
|
