To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 6566 (+10)
  Re: multiplexed touch sensors [was: Re ideas for a RIS 2.0]
 
(...) I don't doubt that there are reasonable creations that e.g. press a touch sensor button halfway for extended periods of time, but I can't think of any off the top of my head. Can anybody help me out here? My point was that in what I would (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
 
  Re: multiplexed touch sensors [was: Re ideas for a RIS 2.0]  [DAT]
 
(...) Okay, I felt like I had some time, so I looked into this a bit. I skipped the first part and jumped right into measuring a waveform. I measured a faster waveforms for now, but might give it another go with a longer waveforms and higher (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
 
  RE: Touch Sensor as a Switch
 
In response to my own post on the Cybermaster touch sensors: The three different Cybermaster touch sensors have a resistance of 15k, 12k, and 10k when not pressed. The rest of my ramblings were pure fiction. The three Cybermaster inputs are (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
 
  Re: robotic rovers
 
(...) Have you tried combining the inputs of the two output motors into a differential? If the inputs are counter-rotating, the net differential body rotation will tell you which side is moving faster, ie: Motor A ------> Differential <--(Reversed (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
 
  Use a RCX as a Sensor port AND a Motor Output!
 
So, I was messing around w/ the RCX and hooked up a Micromotor to one of my output ports and lo and behold....I could control the motor by toggling the Sensor Type for that port between a Passive (None, Switch, Temp) mode = OFF and an Active Mode (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
 
  Re: Use a RCX as a Sensor port AND a Motor Output!
 
Ooops, subject should have been: Use RCX Sensor Port as a Sensor Port AND a Motor Output! Dave (27 years ago, 26-Aug-99, to lugnet.robotics)
 
  Re: Robot related books...?
 
(...) Having cracked mine, I'd have to say "great book". Lots of helpful stuff for the home hobbyist in that one. jack j-perdue@tamu.edu (27 years ago, 26-Aug-99, to lugnet.robotics)
 
  Re: Use a RCX as a Sensor port AND a Motor Output!
 
Great work! Extra motor output, speed sensing, stall detection and sensor/motor multiplexing. Thanks for the research! (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
 
  Re: Climbing robot?
 
Where can I find more info on the Fudd stair climber? I couldn't find anything in the LUGNET newsgroups. (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
 
  Search Sub
 
I just received my search sub today. It was a great deal from shop@home. Half price, just $25. In addition to standard extra parts, it contains an air tank, a large pump and a large piston. Joel Shafer joel@connect.net -- Did you check the web site (...) (27 years ago, 26-Aug-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR