To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 4356 (-10)
  Re: multi-device output controller (fwd)
 
Has anyone tried out the Muscle Wire or electronic pistons from this site? Seems like a good alternative to pneumatics. (...) -- Did you check the web site first?: (URL) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
----- Forwarded message from Jim Choate ----- From: Jim Choate <ravage@ssz.com> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 10:34:22 -0600 (CST) It's actualy pretty easy. Take the analog RCX output, integrate, S&H, A/D, (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
Hi Bill, ----- Forwarded message from Bill Flanagan ----- From: "Bill Flanagan" <bflanagan@mediaone.net> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 11:26:31 -0500 I like the ide that you have but like you, I am not a (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
----- Forwarded message from Bill Flanagan ----- From: "Bill Flanagan" <bflanagan@mediaone.net> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 11:26:31 -0500 How about an RCX to RS232 connection to use off the shelf (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
(...) With a seperate battery box (from 8735 for instance) you could power the output full time. In this case you'd probably want to map it to something like this: off - off 1 - output 1 fwd 2 - output 1 rev 3 - output 2 fwd 4 - output 2 rev 5 - (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
(...) And where are you getting motor drive power from? I assume you want the selected motor to run at full power, not at 1/8, 1/4, etc. I'm afraid you're still stuck consuming the extra output for power unless you use a separate power source. (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
----- Forwarded message from Dennis Clark ----- From: "Dennis Clark" <dlc@verinet.com> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 15:27:53 GMT Ha! I'm one up on ya both. Run a tight loop and find out how fast the RCX (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
(...) [snip] (...) [snip] Ha! I'm one up on ya both. Run a tight loop and find out how fast the RCX can cycle the motors on and off, time it, and send a package a serial message at whatever the fastest BAUD rate is to control a max of N motors with (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  RE: Polarity Switch = Pressure Switch
 
(...) Mine required no tuning at all, if that's what you mean. I tried a similar configuration to lu's and found that the throw was difficult to get right. I don't like the overall size of my regulator, but it works like a champ! Cheers, Ralph (...) (28 years ago, 26-Mar-99, to lugnet.build, lugnet.robotics)
 
  Re: Polarity Switch = Pressure Switch
 
How well does this work? Contrast with: (URL) on (URL) I got from lu, and which seems to require a fair bit of fiddling to get it to regulate correctly. (...) (28 years ago, 26-Mar-99, to lugnet.build, lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR