To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 23374 (-20)
  Re: Johnny five IS alive - first MOC
 
(...) You might find that spreading the hinge plates wider on the tread shoes will help. Having them near the centre increases the "twisting" effect if there are forces near the edge of the shoes. Also, having 3 per shoe instead of 2 may help - mine (...) (22 years ago, 20-Jan-05, to lugnet.robotics, lugnet.build.mecha, lugnet.technic)
 
  RCX IR Tx Circuit
 
Here's my drawing of the RCX IR transmission circuit (receiver circuit to follow soon): (URL) With the voltages as shown, the RCX is not transmitting. The IR LEDs are powered by a 600mA current sink. I haven't measured for waveforms yet - the (...) (22 years ago, 20-Jan-05, to lugnet.robotics, lugnet.robotics.rcx, FTX)
 
  Re: The Great Ball Contraption
 
(...) We look forward to seeing you there... (...) E-mail me your address. (...) I really like to build my stuff with a very clean look. That usually means hiding all the inner workings. That's why the stairs looked like this in my first build: (...) (22 years ago, 20-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) Wow, nearly untouched territory... pumping Steve's... oh, never mind. On a more pratical note, does your pump meet the height requirement for the GBC? I've got two ball pumps working, but both have the same problem - allowing room under the (...) (22 years ago, 20-Jan-05, to lugnet.robotics, FTX)
 
  Re: Johnny five IS alive - first MOC
 
bricksnap wrote: > Yes, treads are working, but moving is rather bumpy. Because of the construction > of the treads and the huge overall weight they easily broke up. I'm a little suprised that you chose to use just one motor for each tread. The (...) (22 years ago, 20-Jan-05, to lugnet.robotics)
 
  Re: AFOL Mindstorm competition in Billund
 
(...) we (FreeLUG : French LUG) are planning on going. We need to know exactly who will go in FreeLUG, but it is almost sure to be present. see you at this competition :-) (22 years ago, 20-Jan-05, to lugnet.robotics)
 
  Re: Johnny five IS alive - first MOC
 
(...) Hi Mark Thanks for your feedback. Yes, treads are working, but moving is rather bumpy. Because of the construction of the treads and the huge overall weight they easily broke up. I'll give my best to make little movies and post it here. First (...) (22 years ago, 20-Jan-05, to lugnet.robotics, lugnet.build.mecha)
 
  Re: Johnny five IS alive - first MOC
 
(...) Hi Thank you for your feedback and for adding my post to .technic. Yes it's true, moving is pretty jerky and because of the huge overall weight the treads will broke up .relatively often. Maybe I'll think about another kind of treads but I'll (...) (22 years ago, 20-Jan-05, to lugnet.robotics, lugnet.build.mecha, lugnet.technic)
 
  Re: AFOL Mindstorm competition in Billund
 
While there's still a week and a half left to sign up for the AFOL Mindstorms competition in Billund, I'm wondering how many new teams are planning on going? Or at least considering it? -- David Schilling (22 years ago, 20-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
What's funny is the other day I was thinking of building a marble machine with LEGO. After reading about this contraption system, I got super-motivated and built myself a ball pump last night. I only spent a few hours on it, but I think I have it (...) (22 years ago, 20-Jan-05, to lugnet.robotics, FTX)
 
  Re: Johnny five IS alive - first MOC
 
Hi Steven I remember seeing this a while back and thinking it wasn't even Lego, until I looked closer, woof. Woof, woof. And not only is it a great model but then you roboticized it as well. Cool. I can't wait to see when your done. This will be (...) (22 years ago, 20-Jan-05, to lugnet.robotics, lugnet.build.mecha)
 
  Re: Johnny five IS alive - first MOC
 
(...) I've added .technic to the groups cos I think they'll like it over there too! Can't wait to see the finished robot - I remember Short Circuit from when I was a kid. One question I have, how smoothly does it move on those treads? I found my (...) (22 years ago, 20-Jan-05, to lugnet.robotics, lugnet.build.mecha, lugnet.technic)
 
  RE: Lego water-freezing rapid prototype machine
 
(...) For those interested, the current issue of Popular Science has a rather larger article devoted to the ink-jet printer and how it has spawned technical growth in the 3D prototyping arena. The article goes in depth on how an ink-jet printer (...) (22 years ago, 19-Jan-05, to lugnet.robotics)
 
  Re: Lego water-freezing rapid prototype machine
 
Hey, Chris! Good to hear from you! There was some discussion of a rapid prototyper started a while back by Steve Baker and I believe he was going to attempt to use expanding 3M insulation foam, laid out in drops as the material. Discussion of other (...) (22 years ago, 19-Jan-05, to lugnet.robotics)
 
  Lego water-freezing rapid prototype machine
 
I seem to recall seeing a creation someone made of a Lego-based rapid prototyping mill that deposited water droplets that froze on contact to build shapes. Was I hallucinating? I can't find it using Google, but I suspect I'm not searching for the (...) (22 years ago, 19-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption 2.0
 
(...) ... (...) But wait, there's more... First, a friend (another Bryan) came over with his module, and then the next day, we had a club meeting, where our whole LEGO club had modules. After running Bryan's for a bit, I considered adding a "Maximum (...) (22 years ago, 19-Jan-05, to lugnet.robotics, lugnet.technic, lugnet.trains, lugnet.events.brickfest) ! 
 
  Johnny five IS alive - first MOC
 
hello all After a long building time (uncounted houres during one and a half year) I finally assembled my Johnny Five robot the first time. This was a great feeling looking to the robot and I will share this with you.I found a lot of inspiration on (...) (22 years ago, 19-Jan-05, to lugnet.robotics, lugnet.build.mecha) !! 
 
  Re: Communicate RCX2 with Spybot
 
(...) Yes, they can communicate using IR. Look at the contents of the MindScript header files included in the LEGO Mindstorms SDK 2.5. Also read the Spybot SDK information regarding its built-in subroutines. In addition to using MindScript you can (...) (22 years ago, 18-Jan-05, to lugnet.robotics)
 
  Re: Communicate RCX2 with Spybot
 
In MacNQC 4.0b, in the preferences, there is a "Spybotics" option in the menu for targets. I don't know if this helps you out at all, but perhaps NQC can help you. Alex wrote: > Hi All, > > I am having RCX2 unit with USB Tower and a spybot. > > Can (...) (22 years ago, 18-Jan-05, to lugnet.robotics)
 
  Re: Communicate RCX2 with Spybot
 
(...) No you can't talk to the RCX brick using the Spybot cable and you can't send programming from a computer through the Spybot and to the RCX. The first is an absolute "No". The second is a nearly absolute "No" since it is theoretically possible (...) (22 years ago, 18-Jan-05, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR