 | | RE: TGBC - The Weakest Link?
|
|
<SNIP> (...) Like a train layout, how about routing/switching module to create multiple ball routes? This way, if any one module acts up, only modules affected in that path need to be dealt with. Given the standards (regarding input/output bin (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Not to oversimplify, but I mean if the 'standard' for the ball contraption is 32 studs from the front of the hopper to the back edge of the baseplate, and thus I personally would probably grab a 32 x 32 stud baseplate to build on, thus the (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Is there something that a module builder can not do because the standard is too simple? Steve (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
Steve Baker writes: > So simply write into the rules that everyone who submits a left hand > turn has to submit a corresponding right hand turn or they won't > be accepted. Excellent idea! But it's even easier than that!! Do NOT change the (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
tmassey@obscorp.com writes: > Or not: leave the standard as it is (except for specifying that the space > above the input belongs to the previous module), and have the organizers > build (or specificially request) out-of-spec modules to accomplish (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
Brian Davis writes: > Instead of that, just make sure that your module delivers through > the "side" of the downstream module's territory. Then the spec should say that the ball should go through a vertical plane, and specify the size of the (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Why not universalize the standard so that a module that can turn must be configurable to turn either to the left or the right? A few ways this could be done are movable output stages, EG a sliding or drop-in output that can be placed where (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Actually, it's pretty interesting, if you consider how complex making a pair of turns really is. If you make a 90 degree right hand turn on a 32x32 baseplate, the module must output right next to it's own input. But, bins on a left-hand turn (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Who will promptly tell you to talk to Nik. They're his, not mine. However I CERTAINLY will be advising him to hold out for good space parts in trade. :) I might have to see if we can build one or two of these, seems like good fun. I might even (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) I think you can handle this with a little care in the design of the rules. If the table you are setting it up on is deep enough to permit it, you could always use four 90 degree pieces in a LEFT/RIGHT/RIGHT/LEFT sequence to keep the overall (...) (22 years ago, 9-Jan-05, to lugnet.robotics)
|