 | | Re: The Great Ball Contraption
|
|
Brian Davis writes: > Instead of that, just make sure that your module delivers through > the "side" of the downstream module's territory. Then the spec should say that the ball should go through a vertical plane, and specify the size of the (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Why not universalize the standard so that a module that can turn must be configurable to turn either to the left or the right? A few ways this could be done are movable output stages, EG a sliding or drop-in output that can be placed where (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Actually, it's pretty interesting, if you consider how complex making a pair of turns really is. If you make a 90 degree right hand turn on a 32x32 baseplate, the module must output right next to it's own input. But, bins on a left-hand turn (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Who will promptly tell you to talk to Nik. They're his, not mine. However I CERTAINLY will be advising him to hold out for good space parts in trade. :) I might have to see if we can build one or two of these, seems like good fun. I might even (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) I think you can handle this with a little care in the design of the rules. If the table you are setting it up on is deep enough to permit it, you could always use four 90 degree pieces in a LEFT/RIGHT/RIGHT/LEFT sequence to keep the overall (...) (22 years ago, 9-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Yeah - I agree. You need the 'average builder' to stick to a simple straight-line standard one-size-fits-all module. If you don't then everyone will want to build something esoteric and you'll get hardly any simple modules of the kind that (...) (22 years ago, 9-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Instead of that, just make sure that your module delivers through the "side" of the downstream module's territory. In other words, using a chute (even a very short one) is a pretty easy solution. And that way the standard isn't further (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Or create other "Types" That's the long-term plan. Of course, any GBC that uses some of these other module types will require considerabily more planning prior to set-up, and it will also make the whole contraption less tolerant to the (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: TGBC - The Weakest Link?
|
|
(...) Not really. :) However, we're not expecting the GBC to run 100% of the time. It's not like letting a train run in a circle for eight hours. There are all kinds of things going on at the same time. In our testing, we seemed to run for about 20 (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: TGBC - The Weakest Link?
|
|
(...) First, test the modules as they are added to the system to make sure they meet the minimum requirement. Second, watch the whole thing like a hawk, being ready to shut it down to fix such problems. Third, there will have to be some (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) The list is on Steve's GBC page, below the Type I standard - just scroll down. (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
"Brian Davis" <brdavis@iusb.edu> wrote in message news:IA02Dv.1DH7@lugnet.com... (...) Hmm I must have missed that list post. I am kind of working on a contraption, but it's main aim is to sort LEGO bricks, which are a lot less likely to slide than (...) (22 years ago, 10-Jan-05, to lugnet.robotics)
|
| |
 | | Re: TGBC - The Weakest Link?
|
|
(...) Any operation involving a long sequence of events as in The Great Ball Contraption (TGBC) is likely to be fouled up by failure of one of the events in the chain - the so called weakest link. Is there allowance for the fact that one of the (...) (22 years ago, 9-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
Russell Nelson <nelson@crynwr.com> wrote on 01/09/2005 04:20:10 PM: (...) Or not: leave the standard as it is (except for specifying that the space above the input belongs to the previous module), and have the organizers build (or specificially (...) (22 years ago, 9-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) I made a device that sends balls alternately down two chutes. Balls enter through a 2x2 hole in the top, onto the centre of a 7L studless beam, set up as a see-saw. Which ever way a ball goes, it drops onto another, longer, see-saw that tilts (...) (22 years ago, 9-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
Steve Baker writes: > Another thought I had was that the organisers might want to consider > building a stage that has one input hopper and TWO outputs that sends > balls alternately to the two places. Yes! Since the soccer and basket balls are the (...) (22 years ago, 9-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
Steve Hassenplug writes: > As you can see, it hangs over it's neighbor a bit. > > Of course, if you ass-u-me anything about the neighboring modules > you could run into problems. You can assume anything that's in the specification! Speaking of (...) (22 years ago, 9-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) That module is pretty simple and small. The whole thing is just 10 studs x 13 studs (with a power cord coming out) Here's a picture I just uploaded to brickshelf. More waiting for moderation. (URL) (22 years ago, 9-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
Steve Hassenplug wrote: <snip> (...) Steve, What can you tell me about the Yellow "step feeder" type device in the "lower left corner" of the GBC ? A step feeder is a solution to a lego idea I wanted to build. How complex is it? Thanks Chris (22 years ago, 8-Jan-05, to lugnet.robotics)
|
| |
 | | Re: The Great Ball Contraption
|
|
(...) Actually, we've tried this. Our first get-together was an all-day event, where we did all sort of messing around. In addition to a ton of soccer balls, I've receintly picked up a few different basket ball sets, including a set that had two (...) (22 years ago, 8-Jan-05, to lugnet.robotics)
|