 | | Re: RCX 2.0 Power Supply
|
| (...) Thanks for pointing that out, Philo. I think I'll stick to the non-hopped up version! :-) (...) Hopefully you didn't find this out the hard way... Mark (22 years ago, 15-Sep-04, to lugnet.robotics, lugnet.trains, FTX)
| | |  | | Re: RCX 2.0 Power Supply
|
| (...) It is nearly impossible to build a power supply that puts out the rated voltage when there is no load. Most will put out too high a voltage (like you have seen), some just shut down. To meassure the voltage of a PS, shorten it with a 1000 Ohm (...) (22 years ago, 15-Sep-04, to lugnet.robotics, lugnet.trains)
| | |  | | Re: RCX 2.0 Power Supply
|
| (...) Indeed, the input capacitor of the RCX is rated 10V, so I would not do that for a too long time. This 1000µF capacitor, used to keep memory during battery exchange, is directly connected to RCX board supply input. By the way, this capacitor is (...) (22 years ago, 15-Sep-04, to lugnet.robotics, lugnet.trains, FTX)
| | |  | | Re: Lego Compatible (was Re: JCX and Legos...)
|
| Joe: I was hoping more people would chime in. Alas, I do not see much interest in this thread right now. Please accept my apologies in advance, my comments below are going to sound like an advertisement ... (...) Such a system already exists and it (...) (22 years ago, 15-Sep-04, to lugnet.robotics)
| | |  | | Re: RCX 2.0 Power Supply
|
| (...) You need to check the voltage while the PS is under load. Pretty much every power supply puts out more when the load is low or nothing. Has to do with loads of factors, but mostly quality of the PS (and (thus) internal resistance of the PS) (...) (22 years ago, 15-Sep-04, to lugnet.robotics, lugnet.trains)
| | |  | | Re: RCX 2.0 Power Supply
|
| (...) On a marginally related note, does someone out there have the equipment to accurately test the output voltage of some typical dc power supplies like the one used for this external ps? I tested every ps I could find in my house (probably 20 or (...) (22 years ago, 15-Sep-04, to lugnet.robotics, lugnet.trains)
| | |  | | RE: Smart Motor
|
| Is this simple enough for you? (URL) Message----- From: PeterBalch [mailto:PeterBalch@c...serve.com] Sent: 15 September 2004 14:58 Cc: [unknown] Subject: RE: Smart Motor (...) years. (...) Yes, I've looked at their circuits. Boy are they (...) (22 years ago, 15-Sep-04, to lugnet.robotics)
| | |  | | RE: Smart Motor
|
| A Friend is a keen railway enthusiast (and also an Electronics engineer) he suggested that you take a look at this site - schematics, PCB layouts code etc is all available MERG - The Model Electronics Railway Group - have been doing this for years. (...) (22 years ago, 15-Sep-04, to lugnet.robotics)
| | |  | | RCX 2.0 Power Supply
|
| I've crossposted to .trains because this will be useful for those wanting to run LDCC with an RCX 2. Hi All, I've posted some photos on Brickshelf of an external power supply for the RCX 2. The nice part about the design is that program memory is (...) (22 years ago, 15-Sep-04, to lugnet.robotics, lugnet.trains, FTX)
| | |  | | Re: RIS Upgrade Kit
|
| (...) My view is: beware of all USB to serial converters. We bought one of each kind that was available in the local shops. Although they were all different brands, the (2000 or XP) Windows driver s/w was identical (not digitally signed by (...) (22 years ago, 15-Sep-04, to lugnet.robotics)
| |