To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 1886 (+10)
  Newbie
 
I am trying to find out what CyberMaster is and where to get it? Can anyone help???...??? Thank You, Clay Aucoin, caucoin@cruiseshoppes.com Information Technologies Director, Web Services Division Cruise & Vacation Shoppes America (URL) 375-0199 x22 (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
 
  Lego Mindstorms on Mac using Virtual PC?
 
I'm new to this list, so forgive me if this has been discussed before. Has anyone managed to get the Lego Mindstorms software/hardware to work on a Mac using Virtual PC? It seems this should be possible, but the cables I currently have to convert (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
 
  RE: Lego Mindstorms on Mac using Virtual PC?
 
One thing that might be hampering you is the cabling. The cable that comes with the Mindstorms kit is a null modem cable in the sense that the RX and TX lines are swapped. (Hense the two female connectors). I haven't checked to see if any of the (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
 
  Re: sensor input mux calculations
 
(...) Thanks, I didn't think of that. Since it is a linear function to convert the measured resistance to the switch values, this is much faster and also has better spacing between the values. Using 300, 600, 1.2k, 2.4k, and 4.8k ohm resistors, you (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
 
  Re: Spririt.ocx / Cybermaster
 
(...) CyberMaster don't have firmware in RAM, only RCX does. That's why you don't have the file. Probably the example is only for RCX users... :-( (...) Here's some WEB sites you may want to check about SPIRIT.OCX programming: LEGO SPIRIT.OCX (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
 
  Re: Help with my IR tower
 
(...) We just got a set for Christmas and have encountered the same problem. It worked like a champ for several hours then suddenly wouldn't download. I've tried fresh batteries, & an AC power supply. Wiping out the firmware and re-downloading (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
 
  Re: Newbee
 
You should probably get off the lego-robotics e-mail list and use the Lugnet.Robotics news group to see the messages. This allows you to see threads and ignore stuff you don't care about. All the messages are copied back and forth to both groups so (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
 
  Re: sensor input mux calculations
 
The lego touch sensors are not simple on/off switches like you guys show. There is at least 500 ohms in series with them when they are closed. They also seem to be slightly touch sensitive. A light touch will read 1.5K while a hard push is close to (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
 
  Re: sensor input mux calculations
 
I'm not talking about using the touch switches. I would make my own switches - probably whiskers - but who knows. The advantage of A/D input is that instead of having two possible states, you have, in this case 1024. Using that fact you can make (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
 
  Re: sensor input mux calculations
 
Sinse it has been real quite at work, I did some designing and came up with what I think would be a solution. Using Sensor ports A & B, these could be tied to sense the channel select lines of a Analog Multiplexer. The C port would be connected to (...) (28 years ago, 30-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR