 | | Re: More input
|
|
A similar scheme can be found at: (URL) Just go to the section about dealing with only three inputs. Mike G. (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: (long) Rotation Sensor from "Extreme Creatures" Fiber Optics
|
|
Great!!!...!!! It works. Now I have two angle sensors (8456 & 8480) :-)))...))) BTW, this is how it works: The led inside is *ON* only when it is under one of the eight holes. It has a (presumably 10K, since I read 523 in raw mode) current-limiting (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: (no subject)
|
|
No. The 10k resistor that pulls up the input line and a resister that is put across the connection form a voltage divider. The formula given calculates the fraction of the voltage that will be at the junction of the two resisters. That voltage is (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: More input
|
|
Check the URL Mike, I hit a dead end. (...) -- Richard Clemens, Associate Professor Computer Science Department West Virginia Wesleyan College 59 College Avenue, Buckhannon, WV 26201 304-473-8421 clemens@wvwc.edu -- Did you check the web site (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: (long) Rotation Sensor from "Extreme Creatures" Fiber Optics
|
|
-I though it was pretty weird reading this elaborate setup to do rotation sensing with a light sensor and a light gizmo. -Its funny that they never really said anything about it in the manual. Is there info on the cd? -Now, if i could just tell (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: (long) Rotation Sensor from "Extreme Creatures" Fiber Optics
|
|
(...) Here are some ideas Maurice Hilarius sent me on the subject. I hope he doesn't mind my reposting them. "1) You attach a smaller wheel on a shaft which is part of the drivetrain. This wheel rotates on the shaft, but with a small amount of (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: (long) Rotation Sensor from "Extreme Creatures" Fiber Optics
|
|
(...) You could make a paper disc that has a radial pattern of 3 repeating colors that the light sensor can distinguish... for example: red, blue, white, red, blue, white... Then by watching the pattern of colors that go by the light sensor, the (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: More input
|
|
Paul Haas found the problem with the URL, but I don't see it posted here. The period on the end of the URL makes it not work. Try this: (URL) Clemens wrote in message <4.1.19981229083143....wc.edu>... (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: sensor input mux calculations
|
|
(...) Here is my understanding of the circuit: AVcc | Rp 10k | A/D input ---...---+---...--- | | | | | | S0 S1 S2 S3 Rc | | | | | R0 R1 R2 R3 | | | | | GND +----+----+----+---- GND Where Rp is the pullup resistor and Rc is the impedence of the (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Extra sensors available in UK
|
|
(...) Legoland Windsor, pah. I went up in mid november, they hadn't a clue. Didn't know when (or even if) sensors would be available. Mind you they hadn't even heard of service packs. Brian Weeks -- Did you check the web site first?: (URL) (28 years ago, 29-Dec-98, to lugnet.robotics)
|