 | | Re: More questions
|
|
(...) Yes! (...) Yes! (...) Yes! But special programming may be required. Look at earlier postings here with several solutions/ideas for putting more than one sensor on a slot. (...) Yes! When reading your questions I think you want this kit. Play (...) (28 years ago, 28-Feb-99, to lugnet.robotics)
|
| |
 | | Re: list/group merge (was RE: Newbie Question.. FAQ?
|
|
Kekoa Proudfoot wrote: snip (...) What's a Handy Board? Gordie -- "It is better to ask a 'stupid question' than to make a stupid mistake." (28 years ago, 28-Feb-99, to lugnet.robotics)
|
| |
 | | Robolab COM Ports
|
|
I am running Robolab and Mindstorms on the same PC (WIN95). I have a modem on COM1 and a touch pad on COM2. In Mindstorms I connected the RCX transmitter to COM4 - but in Robolab the set-up screen only lists COM1 or COM2 as options. So using Robolab (...) (28 years ago, 28-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Working with Legos
|
|
(...) That's an excellent suggestion. Thanks, Max. There are many other tips on Lego robot construction techniques in an article titled The Art of Lego Design by Fred Martin. It's available for download from the Handy Board web site: (URL) have been (...) (28 years ago, 28-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Working with Legos
|
|
My only tip is to stay away from cyanoacrylics. I used superglue to try to attach a motor to a brick, and it started eating away the brick. Stuck like a champ, but I had red "puss" all over the place. (...) (28 years ago, 28-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | I have made a i2c routine for the handy board
|
|
Hello, You want to use the i2c bus (by the SPI connector) with your handy baord ? I have made a routine to use i2c component (PCF 8574, 8591.......) with the handy board. Do you want it ? See you later. Dperonne@aol.com (28 years ago, 28-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Slope in NQC
|
|
Hi Everyone, Can anyone tell me what is the NQC equivalent of the slope parameter in the Spirit.OCX SetSensorMode command. Thanks, David Strike -- Did you check the web site first?: (URL) (28 years ago, 28-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Slope in NQC
|
|
(...) Making mine Dave Baun's words: I think you can already change the slope with the existing calls. Just add the slope to the mode constant... SensorMode(IN_1, SMODE_BOOL + 10); The slope should be between 0 and 31 (inclusive). :-) Laurentino (...) (28 years ago, 28-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Working with Legos
|
|
Some of the sensors that I've used easily attach to the the plates & hlocks with holes using a set of tiny nut, bolts, and washer(s). No damage done to any of the components, and easy to change your mind about where you're going to put it. -kr (28 years ago, 28-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Working with Legos
|
|
I glued a couple of the thin Lego strips to the bottom of my HandyBoard to make it quick and easy to plop the board firmly onto a Lego base yet still have it easily removable. Doing this you must be certain to get the correct Lego spacing, so first (...) (28 years ago, 28-Feb-99, to lugnet.robotics.handyboard)
|