 | | More information for debugging my problem
|
|
I'm the one with the dead HB. When I look at R14 (next to the SPI header) it is black and is very hot. Do I have a dead resistor? Thank You Peter Eacmen BLS petereacmen@usa.net (28 years ago, 30-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Killough's mobile robot platform
|
|
(...) This design will have R2C2's chip set smoking with envy! But it's a platform - so before I buy the missing pieces - how much mass can it carry? Franz-Michael S. Mellbin ----- fmm@fischer-mellbin.com (URL) (28 years ago, 30-Jan-99, to lugnet.robotics)
|
| |
 | | Two piece light sensor.
|
|
Greetings, Well I finally succeeded. I have created two piece light sensor emitter pair. To do this I took the basic light sensor circuit of Malcolm S. Powell (see (URL) and broke it into two pieces. I built the emitter in one brick and the detector (...) (28 years ago, 30-Jan-99, to lugnet.robotics)
|
| |
 | | Re: measure motor torque with a light sensor
|
|
(...) I think this will only work with CM, lights are powered by the RCX and this will probably run the motors all the time. I guess a touch sensor in raw mode would do it, but wouldn't return anything like 0 and 100. What happens when a motor is (...) (28 years ago, 29-Jan-99, to lugnet.robotics)
|
| |
 | | The ultimate in IR proximity detection (when calibrated)
|
|
We have designed a fast moving Mindstorms robot which tends to hit things before seeing them using most of the IR proximity detector implementations published. I was thinking about the recording of an RCX message by video camera on Simen Svale (...) (28 years ago, 29-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Gear Designs
|
|
Go to ftp://cherupakha.med...ple/fredm/ and download "artoflego.pdf" This is THE book on lego setups, a little math, and lego gear design, with lots of what he calls "cliches." Most outstanding document! -----Original Message----- From: Frank (...) (28 years ago, 30-Jan-99, to lugnet.robotics)
|
| |
 | | 3D Models of the RCX unit?
|
|
Hi, if there are good free models available, I'd appreciate it if you mailed them to me. Two different versions - one with colors only, one with textures - would be especially handy. Thanks, Markus. (28 years ago, 30-Jan-99, to lugnet.robotics)
|
| |
 | | DL with a Mac
|
|
Fred- Thank you for the new version DLoader MCL. I can now indeed load the P- code. Useing this Mac 6500 Apple talk off-printer port-I am still finding odd things-very odd things. A week back-I replaced the hex inverter, memory chip, & U6. Now-after (...) (28 years ago, 30-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | Earlier DL post
|
|
Fred- Thank you-it helps when you put the libraries that won't load into the right folder. I shall take up with Newton Labs why the HB won't talk to the HB and says out of date 2.81 code is out of date. Thank you again for all your help. Cappy (...) (28 years ago, 30-Jan-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: ** voltage dropping and current limitting**
|
|
(...) Well, just off the top of my head, when you say "get 16 vac out" how are you determining this, a volt meter set for "Volts AC" or some such? Not, say, an oscilloscope? You will note that almost all meters render "AC Voltage" as the RMS (Root (...) (28 years ago, 30-Jan-99, to lugnet.robotics.handyboard)
|