To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *7206 (-10)
  Small but useful change to firmdl.c
 
Further moping though the ROM image revealed that the address in the start firmware download message is really the firmware entry point. I modified firmdl.c to take this into account. If an entry point is stored in the s-record file, firmdl.c uses (...) (28 years ago, 2-Jan-99, to lugnet.robotics)
 
  RE: legOS ... really a stack question
 
(...) .bss also contains global data initialized to 0, which is even worse if it's not cleared. -Allen -- Did you check the web site first?: (URL) (28 years ago, 2-Jan-99, to lugnet.robotics)
 
  Re: legOS ... really a stack question
 
(...) All off-chip accesses to f000 or higher are memory mapped to the motors. Because accesses to addresses above fb7f are all on-chip or invalid, the motors are effectively memory mapped to f000-fb7f. (...) What are your symptoms again? One (...) (28 years ago, 2-Jan-99, to lugnet.robotics)
 
  Re: legOS ... really a stack question
 
(...) Looking at my memory map, it appears that there is space for the stack in on-chip memory between fdc0 and ff7e (or thereabouts). That's just about 450 bytes. If you need more stack space than that, you'll need to move the stack to off-chip (...) (28 years ago, 2-Jan-99, to lugnet.robotics)
 
  another question
 
Also, how do you switch the light sensor from reflective mode to ambient mode? I suspect that the LED is what's already run down my batteries, and I don't read reflected light, I read ambient light anyway. -- +---...---] | Ickna / Nick H. | (URL) (...) (28 years ago, 2-Jan-99, to lugnet.robotics)
 
  Re: Programming the RCX in VB
 
Hi John, If you're looking for VB5 sources visit the site below. CU Bert Visit my site on Lego, Robot's and Visual Basic at (URL) bericht----- Van: John Cutter <lugnet.robotics@lugnet.com> Aan: lego-robotics@crynwr.com <lego-robotics@crynwr.com> (...) (28 years ago, 2-Jan-99, to lugnet.robotics)
 
  StartOfTask
 
Could somebody clear this up for me? Does this overwrite your current program stored in the RCX, or does it create a new micro program that runs immediately? does this work like a normal program (I.E.: RCX Code) are you restricted to the 5 slot (...) (28 years ago, 2-Jan-99, to lugnet.robotics)
 
  Re: Bonding Lego plastic?
 
If you want to bond Lego brick permanently, use acetone. It will dissolve the ABS and the bricks will be bonded forever! Acetone is found in nailvarnish remover... Dave. -----Original Message----- From: D/ <d_miller@ophley.mv.com> To: (...) (28 years ago, 2-Jan-99, to lugnet.robotics)
 
  Re: legOS ... really a stack question
 
(...) Hmmm ... good point. 0xf000 is memory mapped I/O for the motors, IIRC. Not sure whats above there, but I wouldn't be surprised to hear it isn't a good place to store things. I'd guess that setting the stack to 0xeffe should be equally good. (...) (28 years ago, 2-Jan-99, to lugnet.robotics)
 
  Beat me to it
 
Darn, you beat me to it! I've just been working on that exact feature for my yet-to-be-released program.... I won't copy your code, don't worry, I'll just observe your method... -- ( Ickna / Nick H. ) ( (URL) ) ( Ickna@-nospam-aol.com ) ( Remove (...) (28 years ago, 2-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR