To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *7201 (+10)
  Re: Programming the RCX in VB
 
Hi John, If you're looking for VB5 sources visit the site below. CU Bert Visit my site on Lego, Robot's and Visual Basic at (URL) bericht----- Van: John Cutter <lugnet.robotics@lugnet.com> Aan: lego-robotics@crynwr.com <lego-robotics@crynwr.com> (...) (28 years ago, 2-Jan-99, to lugnet.robotics)
 
  another question
 
Also, how do you switch the light sensor from reflective mode to ambient mode? I suspect that the LED is what's already run down my batteries, and I don't read reflected light, I read ambient light anyway. -- +---...---] | Ickna / Nick H. | (URL) (...) (28 years ago, 2-Jan-99, to lugnet.robotics)
 
  Re: legOS ... really a stack question
 
(...) Looking at my memory map, it appears that there is space for the stack in on-chip memory between fdc0 and ff7e (or thereabouts). That's just about 450 bytes. If you need more stack space than that, you'll need to move the stack to off-chip (...) (28 years ago, 2-Jan-99, to lugnet.robotics)
 
  Re: legOS ... really a stack question
 
(...) All off-chip accesses to f000 or higher are memory mapped to the motors. Because accesses to addresses above fb7f are all on-chip or invalid, the motors are effectively memory mapped to f000-fb7f. (...) What are your symptoms again? One (...) (28 years ago, 2-Jan-99, to lugnet.robotics)
 
  RE: legOS ... really a stack question
 
(...) .bss also contains global data initialized to 0, which is even worse if it's not cleared. -Allen -- Did you check the web site first?: (URL) (28 years ago, 2-Jan-99, to lugnet.robotics)
 
  Small but useful change to firmdl.c
 
Further moping though the ROM image revealed that the address in the start firmware download message is really the firmware entry point. I modified firmdl.c to take this into account. If an entry point is stored in the s-record file, firmdl.c uses (...) (28 years ago, 2-Jan-99, to lugnet.robotics)
 
  Re: legOS errors
 
(...) It is a perl program, and as shipped it expects perl to be in /usr/bin. If you have perl installed in /usr/local/bin (for example), just change the first line to #!/usr/local/bin/perl. If you don't have perl, you will need to obtain and (...) (28 years ago, 3-Jan-99, to lugnet.robotics)
 
  binutils problem fixed
 
Many thanks to those of you that sent a compiled copy of kmain, I was able to determine where the error was. If you are trying to run binutils on a machine that has char as an unsigned type, you will have the same problem. I remember at least one (...) (28 years ago, 3-Jan-99, to lugnet.robotics)
 
  RCX Motor controller IC
 
I tried searching for the data sheet on the RCX motor controllers. The closest fit I can find to the ELEX10402B number from the .jpg images from the (URL) site is a motor controller manufactured by Melexis, the MEX10402. The physical description (...) (28 years ago, 3-Jan-99, to lugnet.robotics)
 
  Off: RCX 2.0 -- ideas.
 
In article <01f401be367e$0ca56e...40d4@jr1>, jr <jr1@casema.net> writes (...) And the UK, too. We used one to automate part of the Llanwern Steelworks in 1975. But that's not the old days. Mercury delay-line RAM is the old days. (28 years ago, 2-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR