To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *6926 (-10)
  RE: sensor input mux calculations
 
Duh. I didn't notice that the switches were in parallel with the resistors. Dang proportional fonts in email. Sorry about that. Yes, it would work nicely and is generally what others have been thinking of, just not putting down in drawings. Rob/Duh (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
 
  RE: sensor input mux calculations
 
This design would prevent multiple switch detection. Only one switch would be detectable (the last one). The designs people have been creating so far have been capable of detecting 3-4 discrete inputs at any time regardless of the settings of any (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
 
  Squeezing 4 inputs out of 1
 
I've constructed a circuit that will read four switches from one input port. Theory- The input port is an A/D circuit. It reads voltage as opposed to state. The A/D line is wired to a 10K ohm resistor that is in turn wired 5 volts. Thus if it is (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
 
  Squeezing 4 inputs out of 1
 
I've constructed a circuit that will read four switches from one input port. Theory- The input port is an A/D circuit. It reads voltage as opposed to state. The A/D line is wired to a 10K ohm resistor that is in turn wired 5 volts. Thus if it is (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
 
  99 Catalog scans complete
 
well, all done scanning them, where to put them? there is a total of 2.61 MB of them, all the new ones up to the Search and Rescue Complex (P 29), will scan the rest tommorw, I ran outta space on my C: drive, where the scanner software holds a temp (...) (28 years ago, 30-Dec-98, to lugnet.general, lugnet.robotics)
 
  Re: sensor input mux calculations
 
Sinse it has been real quite at work, I did some designing and came up with what I think would be a solution. Using Sensor ports A & B, these could be tied to sense the channel select lines of a Analog Multiplexer. The C port would be connected to (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
 
  Re: sensor input mux calculations
 
I'm not talking about using the touch switches. I would make my own switches - probably whiskers - but who knows. The advantage of A/D input is that instead of having two possible states, you have, in this case 1024. Using that fact you can make (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
 
  Re: sensor input mux calculations
 
The lego touch sensors are not simple on/off switches like you guys show. There is at least 500 ohms in series with them when they are closed. They also seem to be slightly touch sensitive. A light touch will read 1.5K while a hard push is close to (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
 
  Re: Newbee
 
You should probably get off the lego-robotics e-mail list and use the Lugnet.Robotics news group to see the messages. This allows you to see threads and ignore stuff you don't care about. All the messages are copied back and forth to both groups so (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
 
  Re: Help with my IR tower
 
(...) We just got a set for Christmas and have encountered the same problem. It worked like a champ for several hours then suddenly wouldn't download. I've tried fresh batteries, & an AC power supply. Wiping out the firmware and re-downloading (...) (28 years ago, 30-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR