To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *4736 (+10)
  Re: Touch Sensor Actuation Force?
 
(...) I don't, but I can tell you that it's trivial. The main issue is the distance the switch needs to be pushed before it triggers, not how hard it's pushed. I've built 'frames' around the sensor such that an almost infinitesimal bump triggers the (...) (28 years ago, 21-Oct-98, to lugnet.robotics, lugnet.build)
 
  Re: Questions about sensors
 
Eric Noyau wrote: <snip> (...) The results you get from a reflective IR sensor will vary quite a lot depending on surface color, roughness, angle of incidence, electrical noise, etc. My IR sensors were not good for much of anything besides encoders, (...) (28 years ago, 21-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Charging batteries
 
(...) Well I will be the first to admit that this is hardly a scientific study but here is my personal experience. For 4 years I have had the same cellular phone and the same notebook computer. The cellular phone is a Motorola with an Intelecharger (...) (28 years ago, 21-Oct-98, to lugnet.robotics)
 
  Basic Sensor Question
 
I just got my HB and am trying to test the sensor input, the docs say to hook up the microswitch between signal and ground, when I do this and close the switch my hb resets (because I just shorted it out...). I tried putting a resistor (330 ohm) in (...) (28 years ago, 21-Oct-98, to lugnet.robotics.handyboard)
 
  RE: RTOS for HB?
 
There is the Micro Kernel from Jean J. Labrosse. It's a free kernel readily available, also for the 68hc11. I have his book but haven't implemented the full kernel yet, only parts of it. Its well written and cheap. Look at: (URL) jaron paludanus (...) (28 years ago, 21-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Basic Sensor Question
 
It sounds like you've got the switch between +5V and GND. What pins exactly are you connecting to? The sensor connections Are like this: _ _ _ G + I N 5 N D V P You dont need a resistor to use a microswitch. The HB inputs have pull-up resistors, so (...) (28 years ago, 21-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Basic Sensor Question
 
You were right, also it seems my board is wired incorrectly analog(0) controls the connector marked 7 on the hb. Thanks for your help! Julian -----Original Message----- From: Scott R. Harris <srharris@phoenix.Pr...ceton.EDU> To: Julian Porter (...) (28 years ago, 21-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Basic Sensor Question
 
if a sensor connector row looks like this -- [ ][ ][ ][ ][ ][ ][ ] [ ][ ][ ][ ][ ][ ][ ] [ ][ ][ ][ ][ ][ ][ ] 6 5 4 3 2 1 0 then to connect to sensor 0, you plug the switch into the places marked "[X]": [ ][ ][ ][ ][ ][ ][X] [ ][ ][ ][ ][ ][ ][ ] [ (...) (28 years ago, 21-Oct-98, to lugnet.robotics.handyboard)
 
  train AC adapter for RCX?
 
Hi, Someone may have mentioned this earlier... The AC adapter port on the RCX indicates a 9-12V AC input. Does this mean it'll work with the train regulator AC adapter? Thanks, -Tim (28 years ago, 22-Oct-98, to lugnet.robotics)
 
  Read A/D converter
 
"HI" , I am trying to read the A/D converter but the program gets "Hung-Up" on the line "ANALOOP", the CCF bit never sets. Please give me a hint. Here is the Assembly code. /* MAGLEV.ASM, Magnetic Levitation by Hector Noriega, 28JUNE1998.*/ /*Handy (...) (28 years ago, 22-Oct-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR