 | | Custom firmware crashing on boot
|
|
Hey, I'm new here, so if I seem like a n00b, it's probably because I am. Hopefully my question won't be too annoying. I'm trying to use the NXTGCC 0.0.9 package as a starting point for custom firmware. The main point of my custom firmware is to swap (...) (17 years ago, 27-Jun-07, to lugnet.robotics.nxt.nxthacking)
|
| |
| | Temporarily removing official NXT driver to use SAM-BA
|
|
Hey, I tried to post this message two days ago and it hasn't shown up yet, so I'm trying again (with a different client in case that's why it was eaten). If people receive duplicates, I sincerely apologize. Message follows: Hey, I apologize in (...) (17 years ago, 27-Jun-07, to lugnet.robotics.nxt)
|
| |
| | Re: Re Rafe Donahue's GBC binary counter
|
|
(...) Hi Jordan, You are right; Rafe's counter actually does this already. The only mod would be the storage trays you mentioned. In fact, during down times at Brickworld, I often mention that the machine is really an adding maching and all we are (...) (17 years ago, 25-Jun-07, to lugnet.robotics)
|
| |
| | Re Rafe Donahue's GBC binary counter
|
|
I saw this and was reminded of Rafe's binary counter: (URL) a marble-powered binary adder. Rafe's counter could do this with a tiny bit of modification. He'd just have to add a tray at the top and bottom to temporarily store the input and output for (...) (17 years ago, 25-Jun-07, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: LEGO Engineer Software
|
|
Some explenations regarding the Lego Engineer Version I suggested before: The version is Lego Engineer 2.0 and it will work only on top of Robolab 2.0, so if you have a newer version of Robolab - 2.5.4 specifically, You should download the newest (...) (17 years ago, 25-Jun-07, to lugnet.robotics)
|
| |
| | Re: lcd display on RCX 1.0
|
|
(...) If you load RCX2 firmware in a RCX1 brick (they are fully compatible*), you'll have acces to this function (and all other RCX2 specific possibilities) Philo *Except for some minor differences in IR hardware. (17 years ago, 25-Jun-07, to lugnet.robotics.rcx.nqc)
|
| |
| | lcd display on RCX 1.0
|
|
NQC: with RCX2, it has a function to display a user defined value. Is there a way to do it with RCX 1.0? How about just to display the current mail value with RCX1.0? Suggestion? Thanks in advance. --Elizabeth (17 years ago, 24-Jun-07, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Clicking NXT
|
|
That did the trick Dick. Thanks (17 years ago, 23-Jun-07, to lugnet.robotics)
|
| |
| | RE: Clicking NXT
|
|
May be obvious, but are the batteries fully charged? You get unpredictable effects with marginal battery voltage and attempting to write to flash memory. -----Original Message----- From: news-gateway@lugnet.com [mailto:news-gateway...ugnet.com] On (...) (17 years ago, 23-Jun-07, to lugnet.robotics)
|
| |
| | Re: Clicking NXT
|
|
(...) I'm pretty sure I updated the driver, but just to make sure I did it again. I still have a maddeningly fast clicking NXT. I can hear it now, buried beneath the floor boards. click Click CLICK. Why do you pretend not to hear it? CLICK! CLICK!! (...) (17 years ago, 23-Jun-07, to lugnet.robotics)
|
