To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *44849 (-10)
  NBC News for NXT
 
Over the weekend I got my new Mac Mini G4 up and running, installed lots of development tools, copied over my NBC sourcecode and managed to build a working version of the NBC compiler for the NXT brick. I will have a zip containing the Mac version (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) I'll get to that, eventually... there's just too much fun stuff going on, and... (...) A historical point on this. The first time I met Steve was at a sumo event, where I had carefully calculated the correct gear ratio, given the torque of a (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) Not so obvious. If you increase the surface the pressure per surface unit decreases proportionnaly (at least on hard surface)... Actually I would expect little or no variation in traction power. Philo (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) Hmmm - that's unfortunate...but if the 'right' strategy is to go with a non-slipping robot, the measurement of sliption is really a lot less important. (...) Yeah - so many of those basic mechanics equations are only approximations - yet they (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) hmm. This sounds like a good project... (...) All things being equal, I'd put my money on the robot with ten spinning wheels, over a couple (or even ten) stationary ones. I'd also mechanically connect all the motors together, so they drive a (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) As you note in your mini-cooper example, *if* you can keep the wheels from "spinning out", but instead are always in rolling contact with the ground, static friction is what's important... and generally, the static coefficient of friction is (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) That makes sense. (...) Yeah - I agree. So we have to sum some force vectors here. If our robot is pulling to the left, we have a horizontal 'drive' force to the left and a force in the tow rope going off to the right - plus a force due to (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) Dave, Actually I am very happy and grateful. I am getting a crash course. Couldn't have asked for more. Raj. (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) Steve Hassenplug, Sorry, my mistake. Thank you for the Wiki link and all your help. Raj. (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) The problem is that this is measuring the static friction ("stiction"). That's the wrong thing to measure if your strategy is to jam all the motors full on and progress forwards (we hope!) with all wheels spinning. To measure the dynamic (...) (20 years ago, 7-Jun-06, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR