 | | Re: Could we all let it alone? (Was Re: Moonbase Module - Mech Bay 07)
|
|
(...) <major snippage (down to the tech)> Thanks Eric, I appretiate the reply. I have seen a few posts here and there that I find personally irrelevant - and mreely pass them by. I have also occasionally been attacked by posters. In my case it has (...) (21 years ago, 22-Sep-05, to lugnet.build.mecha, lugnet.robotics)
|
| |
 | | Re: Rotating through a four-bit nibble
|
|
(...) Maybe it is time to move on to BrickOS? int rotate_right( int value, // the value to be rotated int width, // the width of the rotated field int base, // bitnumber of rightmost bit in rotate field int amount) // the amount to rotate between (...) (21 years ago, 22-Sep-05, to lugnet.robotics)
|
| |
 | | Re: Rotating through a four-bit nibble
|
|
(...) Both your 1st & 2nd solutions are very good; thanks to you and other posters to this thread for giving me a much better handle on binary manipulations, and solutions to this problem. In answer to an earlier question, speed is important (simple (...) (21 years ago, 22-Sep-05, to lugnet.robotics)
|
| |
 | | Re: A LEGO double-throw switch?
|
|
(...) First, I learned a *lot*, so thank you all. As for which "solution" I ended up using, first disclaimer, I've not yet built a "crate conveyor". But some prototyping showed that the tank treads just have too much bending friction for what I (...) (21 years ago, 22-Sep-05, to lugnet.robotics)
|
| |
 | | Swan scheduling bug?
|
|
I'm starting to use the swan firmware and I'm having a problem with the scheduling. It seems like a task with a long wait does not yield properly to other tasks. Here the NQC code sample: task taska() { WaitMS(150); AddToDatalog(9900); } task main() (...) (21 years ago, 22-Sep-05, to lugnet.robotics.rcx)
|
| |
 | | Re: Rotating through a four-bit nibble
|
|
"Jordan Bradford" <bradfj23REMOVE_THIS...uwosh.edu> wrote in message news:In7A20.1sK1@lugnet.com... (...) The problem is, multiplication and division to a binary CPU, as is the case here, is just a whole series of instructions. Here is the basic (...) (21 years ago, 22-Sep-05, to lugnet.robotics)
|
| |
 | | Re: Rotating through a four-bit nibble
|
|
(...) Why in the world wouldn't the firmware support shifting? The hardware (URL) certainly does>. Heh, using multiply and divide to simulate shifting is kind of backwards. (21 years ago, 22-Sep-05, to lugnet.robotics, FTX)
|
| |
 | | pbrick and firmware
|
|
Palm 130, pbrick, rcx 1.0 Can the palm 130 with pbrick be used to control an rcx that doesn't have firmware downloaded? My suspicion is that it won't work without the firmware. Tammy (21 years ago, 22-Sep-05, to lugnet.robotics.rcx)
|
| |
 | | Re: Rotating through a four-bit nibble
|
|
(...) Since I didn't really complete the assignment I'll try again. I didn't honor the x bit request. I confirmed that even SDK v2.5 does not have shifts or rotates, and that in NQC you can only do shifts based on constant amounts. The two routines (...) (21 years ago, 21-Sep-05, to lugnet.robotics)
|
| |
 | | Re: A LEGO double-throw switch?
|
|
(...) So.... what was the final solution for this? Kev (21 years ago, 21-Sep-05, to lugnet.robotics)
|