 | | Re: Rotating through a four-bit nibble
|
|
"Jordan Bradford" <bradfj23REMOVE_THIS...uwosh.edu> wrote in message news:In7A20.1sK1@lugnet.com... (...) The problem is, multiplication and division to a binary CPU, as is the case here, is just a whole series of instructions. Here is the basic (...) (21 years ago, 22-Sep-05, to lugnet.robotics)
|
| |
 | | Re: Rotating through a four-bit nibble
|
|
(...) Why in the world wouldn't the firmware support shifting? The hardware (URL) certainly does>. Heh, using multiply and divide to simulate shifting is kind of backwards. (21 years ago, 22-Sep-05, to lugnet.robotics, FTX)
|
| |
 | | pbrick and firmware
|
|
Palm 130, pbrick, rcx 1.0 Can the palm 130 with pbrick be used to control an rcx that doesn't have firmware downloaded? My suspicion is that it won't work without the firmware. Tammy (21 years ago, 22-Sep-05, to lugnet.robotics.rcx)
|
| |
 | | Re: Rotating through a four-bit nibble
|
|
(...) Since I didn't really complete the assignment I'll try again. I didn't honor the x bit request. I confirmed that even SDK v2.5 does not have shifts or rotates, and that in NQC you can only do shifts based on constant amounts. The two routines (...) (21 years ago, 21-Sep-05, to lugnet.robotics)
|
| |
 | | Re: A LEGO double-throw switch?
|
|
(...) So.... what was the final solution for this? Kev (21 years ago, 21-Sep-05, to lugnet.robotics)
|
| |
 | | Re: Rotating through a four-bit nibble
|
|
(...) Well, your example has the nibble of interest in the middle of the register. Due to boundary conditions, it might be cheaper to have it in the least significant bits of the 16 bit register. In your example you are rotating by an aribtrary (...) (21 years ago, 21-Sep-05, to lugnet.robotics)
|
| |
 | | Re: time sampling under the rcx standard OS
|
|
(...) Here's a code byte from my LegWay code. ---- int MotorSpeedArray[32] = {1,3,2,0}; // Speeds // ... later in the program... if (sys_time>CheckTime) // check system timer - is it time to check sensors again? { L1 = ReadSensor(SENSOR_1); L3 = (...) (21 years ago, 21-Sep-05, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: New NASA challenge
|
|
(...) The Centennial Challenges in general would probably be a good fit for Mindstorms. (URL) seems the Elevator2010 competition could easily be adapted for use with Lego and Mindstorms (sans beam power). Just decide on a commonly available ribbon (...) (21 years ago, 21-Sep-05, to lugnet.robotics)
|
| |
 | | Re: time sampling under the rcx standard OS
|
|
Hi Steve, As I'm quite new to BrickOS and to C programming, I'm sorry I'm not sure I understood what you meant, neither how you do this : (...) - Do you check the sensor at a higher rate, and only send a command to the motor at 1kHz ? - How do you (...) (21 years ago, 21-Sep-05, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Beeesh Art
|
|
(...) Pardon me Mr. Staple, I was unable to type a proper response containing additional technical data as I promised. I ended up working on two different projects this evening. I had a productive night. When I did sit down to the computer I found (...) (21 years ago, 21-Sep-05, to lugnet.build.mecha, lugnet.robotics)
|