To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *42584 (-10)
  Re: Custom sensor current drain - use two sensor ports?
 
(...) I take it all back. I'm so brilliant that I found a way to make a (rather large) change to the circuitry that brought things under the limit. Ok, ok, forgive my indulgent self-back-patting, but I'm pretty bouyant right now - everything is (...) (21 years ago, 30-Jun-05, to lugnet.robotics.rcx)
 
  Re: Custom sensor current drain - use two sensor ports?
 
Hi Justin, (...) No, the internal circuis are more or less the same. (...) I don't think you could break something. But of course using two input ports is not so great... (...) You might try the kind of trick I used for my GP2D12 sensor ((URL) store (...) (21 years ago, 30-Jun-05, to lugnet.robotics.rcx)
 
  Re: Custom sensor current drain - use two sensor ports?
 
Maybe you could use one of the output ports. It might be worth running the sensor schematic by some of those on the board, while I understand the need to keep things under your hat - others may be able to suggest ways of bringing its consumption (...) (21 years ago, 30-Jun-05, to lugnet.robotics.rcx)
 
  Custom sensor current drain - use two sensor ports?
 
I'm building a custom active mindstorms sensor, but it requires 28mA to operate, while the sensor port only provides about 15mA. Any advice? (The mA requirements of the sensor cannot be halved - improvements may be possible, but it seems unlikely I (...) (21 years ago, 30-Jun-05, to lugnet.robotics.rcx)
 
  Re: What should you do with a stuck motor?
 
Citando Steve Hassenplug <Steve@TeamHassenplug.org>: On Wed, June 29, 2005 4:19 pm, Jordan Bradford said: > Last night I had a new-style 9V motor attached directly to a 40-tooth gear that > was turning an 8-tooth gear. There was a fair amount of (...) (21 years ago, 30-Jun-05, to lugnet.robotics)
 
  Re: R2D2 Sounds - A Warning my RCX has laryngitis.
 
(...) Hi Dick. No the frequency and loop number are managed by containers, but the note duration was set by using a control (or directly specified) in the version that caused the problem. (21 years ago, 29-Jun-05, to lugnet.robotics)
 
  Re: What should you do with a stuck motor?
 
On Wed, June 29, 2005 4:19 pm, Jordan Bradford said: (...) The folks at LEGO are VERY good about replacing messed up motors. I've done it all on-line, before. Steve (21 years ago, 29-Jun-05, to lugnet.technic, lugnet.robotics)
 
  What should you do with a stuck motor?
 
Last night I had a new-style 9V motor attached directly to a 40-tooth gear that was turning an 8-tooth gear. There was a fair amount of torque involved, and my motor stalled after a while. Now the thing won't turn unless I really force it. What (...) (21 years ago, 29-Jun-05, to lugnet.technic, lugnet.robotics, FTX)
 
  RE: R2D2 Sounds - A Warning my RCX has laryngitis.
 
The note duration must be a compile time constant. By any chance were you trying to use a run-time variable (Robolab container) for this? This could explain your problem. -----Original Message----- From: news-gateway@lugnet.com (...) (21 years ago, 29-Jun-05, to lugnet.robotics)
 
  Re: Does any RCX firmware allow a variable to survice shutdown?
 
Thanks for your help everyone. As predicted, it was simply that I was defining my variables in the program, and it hadn't occurred to me that they were already persistant and I was actually resetting them myself. Can there ever be a better answer (...) (21 years ago, 29-Jun-05, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR