To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *41589 (-10)
  Re: Johnny five IS alive - first MOC
 
(...) --snip-- good idea,I have a lot of hinge plates in my depot. So I will give a try. -------- (...) -- snip -- Yes the 4x plates are really "stressed" turning around the wheels. I think the combination of both, smaller plates and re-arangeing (...) (22 years ago, 21-Jan-05, to lugnet.robotics, lugnet.build.mecha, lugnet.technic)
 
  Re: The Great Ball Contraption 2.0
 
Keep up the great work guys! :) Iain (22 years ago, 21-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption 2.0
 
In lugnet.robotics, Steve Hassenplug wrote: (snip) (...) (snip) Nevermind the controls, how'd you build the hopper? ;-) I really like your solution, with the rotating arm that unloads it, creating an auto-reset for the hopper. I've been frustrated (...) (22 years ago, 21-Jan-05, to lugnet.robotics, lugnet.trains)
 
  IR Tower Building
 
Dear List, I am without an IR tower for my Mindtsorms kit. I have built two of the schematics here: (URL) of the ones I tried work. I tried the one by John Barnes, and the hardwire cable. I do not know enough about schematics to read the OEM design. (...) (22 years ago, 20-Jan-05, to lugnet.robotics)
 
  Re: Johnny five IS alive - first MOC
 
Hi Stefan, I've seen bits and pieces of this as you've posted them to Brickshelf, but it's great the see Johnny in all his glory. I can't wait to see this completed. I hope that eventually you're able to post movies of him in action. Bruce (22 years ago, 20-Jan-05, to lugnet.robotics, lugnet.build.mecha)
 
  Re: Johnny five IS alive - first MOC
 
(...) Perhaps switching to 2x plates instead of 4x for the tread surfaces would help - this would help to smooth the curve around the wheels, at the cost of almost doubling the number of hinges you would need to add. Otherwise, love this MOC. Great (...) (22 years ago, 20-Jan-05, to lugnet.robotics, lugnet.build.mecha, lugnet.technic)
 
  Re: Johnny five IS alive - first MOC
 
(...) You might find that spreading the hinge plates wider on the tread shoes will help. Having them near the centre increases the "twisting" effect if there are forces near the edge of the shoes. Also, having 3 per shoe instead of 2 may help - mine (...) (22 years ago, 20-Jan-05, to lugnet.robotics, lugnet.build.mecha, lugnet.technic)
 
  Re: RCX IR Tx Circuit
 
(...) Thanks for all your work on this Mark! It is very interesting, even for someone like me with only basic knowledge of electronics. Are you planning to put it all together on a web page some day? ROSCO (22 years ago, 20-Jan-05, to lugnet.robotics.rcx, FTX)
 
  RCX IR Tx Circuit
 
Here's my drawing of the RCX IR transmission circuit (receiver circuit to follow soon): (URL) With the voltages as shown, the RCX is not transmitting. The IR LEDs are powered by a 600mA current sink. I haven't measured for waveforms yet - the (...) (22 years ago, 20-Jan-05, to lugnet.robotics, lugnet.robotics.rcx, FTX)
 
  Re: Today's Challenge
 
(...) <snippage> (...) Thankyou, Claude. Now as to your further comments: I think that there is likely to be much merit in your words. I have not been able to transfer them into code as yet and so beg your further indulgence. In (very) pseudocode I (...) (22 years ago, 20-Jan-05, to lugnet.robotics.rcx.robolab)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR