To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *41584 (-10)
  Re: Johnny five IS alive - first MOC
 
(...) Perhaps switching to 2x plates instead of 4x for the tread surfaces would help - this would help to smooth the curve around the wheels, at the cost of almost doubling the number of hinges you would need to add. Otherwise, love this MOC. Great (...) (22 years ago, 20-Jan-05, to lugnet.robotics, lugnet.build.mecha, lugnet.technic)
 
  Re: Johnny five IS alive - first MOC
 
(...) You might find that spreading the hinge plates wider on the tread shoes will help. Having them near the centre increases the "twisting" effect if there are forces near the edge of the shoes. Also, having 3 per shoe instead of 2 may help - mine (...) (22 years ago, 20-Jan-05, to lugnet.robotics, lugnet.build.mecha, lugnet.technic)
 
  Re: RCX IR Tx Circuit
 
(...) Thanks for all your work on this Mark! It is very interesting, even for someone like me with only basic knowledge of electronics. Are you planning to put it all together on a web page some day? ROSCO (22 years ago, 20-Jan-05, to lugnet.robotics.rcx, FTX)
 
  RCX IR Tx Circuit
 
Here's my drawing of the RCX IR transmission circuit (receiver circuit to follow soon): (URL) With the voltages as shown, the RCX is not transmitting. The IR LEDs are powered by a 600mA current sink. I haven't measured for waveforms yet - the (...) (22 years ago, 20-Jan-05, to lugnet.robotics, lugnet.robotics.rcx, FTX)
 
  Re: Today's Challenge
 
(...) <snippage> (...) Thankyou, Claude. Now as to your further comments: I think that there is likely to be much merit in your words. I have not been able to transfer them into code as yet and so beg your further indulgence. In (very) pseudocode I (...) (22 years ago, 20-Jan-05, to lugnet.robotics.rcx.robolab)
 
  Re: The Great Ball Contraption
 
(...) We look forward to seeing you there... (...) E-mail me your address. (...) I really like to build my stuff with a very clean look. That usually means hiding all the inner workings. That's why the stairs looked like this in my first build: (...) (22 years ago, 20-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) Wow, nearly untouched territory... pumping Steve's... oh, never mind. On a more pratical note, does your pump meet the height requirement for the GBC? I've got two ball pumps working, but both have the same problem - allowing room under the (...) (22 years ago, 20-Jan-05, to lugnet.robotics, FTX)
 
  Re: Johnny five IS alive - first MOC
 
bricksnap wrote: > Yes, treads are working, but moving is rather bumpy. Because of the construction > of the treads and the huge overall weight they easily broke up. I'm a little suprised that you chose to use just one motor for each tread. The (...) (22 years ago, 20-Jan-05, to lugnet.robotics)
 
  Re: AFOL Mindstorm competition in Billund
 
(...) we (FreeLUG : French LUG) are planning on going. We need to know exactly who will go in FreeLUG, but it is almost sure to be present. see you at this competition :-) (22 years ago, 20-Jan-05, to lugnet.robotics)
 
  Re: Johnny five IS alive - first MOC
 
(...) Hi Mark Thanks for your feedback. Yes, treads are working, but moving is rather bumpy. Because of the construction of the treads and the huge overall weight they easily broke up. I'll give my best to make little movies and post it here. First (...) (22 years ago, 20-Jan-05, to lugnet.robotics, lugnet.build.mecha)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR