To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *41534 (-10)
  Re: Technic plates
 
(...) This sounds like a good idea. What size drill bit did you end up using? (22 years ago, 14-Jan-05, to lugnet.technic, lugnet.robotics)
 
  Technic plates
 
I was just putting together the classroom packs I use for teaching robotics. Each two student team is given a tray of "standard" parts to work with. To make life easier I have tried to "color-coded" these sets with all components (as much as (...) (22 years ago, 14-Jan-05, to lugnet.technic, lugnet.robotics) ! 
 
  Re: combining LDCC and NQC style automation?
 
(...) If you'd rather do a little hardware work, than learn pbForth, I have a couple suggestions. 1) You could use LEDs instead of regular lights. An LED will only light, when the power is going the correct direction. So you could connect 1 LED to (...) (22 years ago, 14-Jan-05, to lugnet.robotics.rcx, lugnet.trains)
 
  Re: combining LDCC and NQC style automation?
 
[big snip] (...) I do have DCC in the latest pbForth, but I've sort of dropped official support for older versions of MacOS. That being said, I think the instructions are still up on the site for getting it to work. :-) Please post here if you;re (...) (22 years ago, 14-Jan-05, to lugnet.robotics.rcx, lugnet.trains)
 
  Re: combining LDCC and NQC style automation?
 
Christopher Masi wrote: [snip] (...) [snip] (...) I know, replying to myself, bad form. I have also discovered that pbForth has DCC worked into it. The good new here (although I have only looked at the introduction on the home page) is that Raplph (...) (22 years ago, 14-Jan-05, to lugnet.robotics.rcx, lugnet.trains)
 
  Re: sub programs
 
"Elizabeth Mabrey" <emabrey@storming-robots.com> wrote in message news:200501140706.j0...ing.com... (...) Both RCX 1.0 and 2.0 use the same firmware which supports 40 total subroutines. Subroutines are dedicated to the five program slots so that (...) (22 years ago, 14-Jan-05, to lugnet.robotics.rcx.robolab, lugnet.robotics.rcx)
 
  RE: sub programs
 
Ok... I figured that out how to make sub-vi have that linked inside a vi. The question about the RCX 2.0's capability still remains unknown... --thanks (...) (22 years ago, 14-Jan-05, to lugnet.robotics.rcx.robolab, lugnet.robotics.rcx)
 
  Re: MOC: Egglift, a Lego Appliance to cook soft-boiled eggs
 
(...) Hello Samarth Thanks for the comments. Me too, I was thinking I could have get some melting problems. I did some gradually tests and to my surprised, despite the high heat I damaged absolutely no parts! The two support beam above are located (...) (22 years ago, 14-Jan-05, to lugnet.robotics, FTX)
 
  sub programs
 
Hi I wonder if I can call a sub program (another vi) within a program. There is an icon command for inserting another vi program into a program, but it does not seem to be a usable function though. Please advise. I understand the maximum of (...) (22 years ago, 14-Jan-05, to lugnet.robotics.rcx.robolab, lugnet.robotics.rcx)
 
  Re: combining LDCC and NQC style automation?
 
(...) Ah, so you have dabbled with LDCC? Gave up? Not enough fun for the amount of effort? Or will you be going back to it? (...) Oh, I was just expecting to send power out the top of the motor to light the light, and have a small technic motor (...) (22 years ago, 14-Jan-05, to lugnet.robotics.rcx, lugnet.trains)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR