To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *41379 (-10)
  Re: Define Event icon...
 
(...) The condition of being equal to 3 is not an event. However, the action of transitioning to 3 is. I'd use the "set up normal event" command followed by the "define event" command. Set the upper threshold to 4, the lower to 2, and the duration (...) (22 years ago, 2-Jan-05, to lugnet.robotics.rcx.robolab)
 
  Re: questions on events
 
(...) See previous post for the "I-don't-actually-do-Robolab" disclaimer, but, since Robolab & NQC both work on the same firmware... You can monitor multiple events, but only in *different* tasks. In other words, (to my knowledge) you can not "nest" (...) (22 years ago, 2-Jan-05, to lugnet.robotics.rcx.robolab, lugnet.robotics.rcx.nqc)
 
  Re: Define Event icon...
 
(...) I fear I became very frustrated with Robolab, so can't help you *specificly* with that enviroment, but... at a firmware level, events can "watch" several different sources: sensors, timers, three simple counters... however, they can not be (...) (22 years ago, 2-Jan-05, to lugnet.robotics.rcx.robolab, lugnet.robotics.rcx.nqc)
 
  Re: Define Event icon...
 
(...) Elizabeth, you are a few steps ahead of me in working with 'Events'. Could you explain, in plain English, what exactly an 'Event' is? ...it's not a 'State' because it can be a constant or a variable. Yet you can have an 'Event Fork' which is (...) (22 years ago, 2-Jan-05, to lugnet.robotics.rcx.robolab, lugnet.robotics.rcx.nqc)
 
  Define Event icon...
 
Hi I'd like to set up an event to watch for a containers value = 3. I am trying to use the "Define Event" icon, but has no luck yet. Just wonder if there is anyone out there has suggestion. The official doc does not explain much different from what (...) (22 years ago, 2-Jan-05, to lugnet.robotics.rcx.robolab, lugnet.robotics.rcx.nqc)
 
  questions on events
 
Are events stackable? Or it works more like "signal()", e.g. in C? e.g. I have 2 different light sensor events set to watch for value higher than 42, yellow & blue. Let say both sensors read 45 at the same time, RCX returns only one event being (...) (22 years ago, 2-Jan-05, to lugnet.robotics.rcx.robolab, lugnet.robotics.rcx.nqc)
 
  Re: 2-wheelers
 
I've been looking at that little piece of code, and trying to duplicate its effect in my YAL-based program, without much luck. When I had Steve's code running, it did tend to stay in one spot, but it eventually became unstable. At this point I plan (...) (22 years ago, 2-Jan-05, to lugnet.robotics)
 
  Re: RCX IR Transceiver and Sensor Port Circuits
 
hi Mark, i have learned a lot from your RCX IR Transceiver Circuit. Things i did not know before. But please dont forget to show us that Sensor Board Circuit. As far as i know, a real introduction into designing RCX selfmade Sensors is not available (...) (22 years ago, 1-Jan-05, to lugnet.robotics)
 
  New invention instructions
 
Where can I get new inventions and their building instructions besides those given in Lego Mindstorms Robotics Invention System 2.0? (22 years ago, 1-Jan-05, to lugnet.robotics)
 
  Re: 2-wheelers
 
(...) I think another huge difference (for me at least) is that Steve's code learns where the upright position is, while most of the others need to be put down in the correct position. (That is what the piece of code does in the 50ms if()). John (22 years ago, 1-Jan-05, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR