To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *41314 (-10)
  RE: Latest Version of ROBOLAB
 
Jerry, I purchased the "B" from the lego site, www.legoeducation.com . I was asking for the difference between the 2.5.4 & 2.5.4B as well, but have not received response yet. Anyone? -- E (...) (22 years ago, 24-Dec-04, to lugnet.robotics.rcx.robolab)
 
  Latest Version of ROBOLAB
 
Elizabeth Mabrey, in her last post, referenced ROBOLAB 2.5.4B. I have just procured a copy from my Spectrum (distributor in Canada) but it is 2.5.4 (without the 'B'). Do I not have an up-to-date copy? ...or, is there a download for 'B' somewhere? (...) (22 years ago, 24-Dec-04, to lugnet.robotics.rcx.robolab)
 
  Re: Replacement Firmware Released
 
I can say with assurance that the firmware that shipped with my RIS 2.0 does indeed brake fully no matter what the power. I started looking into this precisely because the new firmware behaves differently. If that's a feature and not a bug, fine -- (...) (22 years ago, 24-Dec-04, to lugnet.robotics)
 
  Re: Replacement Firmware Released
 
(...) Agreed. For practical reasons, Ultimate Robolab implements the variable brake mode too. (22 years ago, 24-Dec-04, to lugnet.robotics)
 
  Re: Replacement Firmware Released
 
(...) I don't think this is a bug in the original firmware, but rather a protection against burning electronics parts in the RCX or dammaging motors flipping the motor directions too rapidly. Motors present some interesting electronics behaviour due (...) (22 years ago, 24-Dec-04, to lugnet.robotics)
 
  Re: Replacement Firmware Released
 
I'm pretty sure that variable strength braking is in fact the implementation in the standard firmware. Braking is proportional to the current setting of the power level. I think there may even be some ancient posts somewhere in Lugnet on this topic. (...) (22 years ago, 23-Dec-04, to lugnet.robotics)
 
  Re: Replacement Firmware Released
 
The behavior you've experienced is expected. Standard Lego firmware implements a 100 msec delay when you directly "flip" or change powered motor direction. I expect it is a bug (rather than design intent) that if you go through the stage (...) (22 years ago, 23-Dec-04, to lugnet.robotics)
 
  Re: Replacement Firmware Released
 
Hi Dan, (...) that is strange, are you sure? (...) That is what the ROM routines do, and firmwares like Lejos that rely on it. I would have thought the standard firmware does it in the same way. Jürgen (22 years ago, 23-Dec-04, to lugnet.robotics)
 
  Re: RCX IR Transceiver and Sensor Port Circuits
 
Hi Mark, (...) I would also like to see your diagrams. (...) Please use GIF or PNG, jpegs are not so good for diagrams. Jürgen (22 years ago, 23-Dec-04, to lugnet.robotics)
 
  RCX IR Transceiver Circuit
 
(...) I managed to get this one drawn today: (URL) N.B. I cannot guarantee accuracy as this is my own interpretation of the circuit of my own IR Transceiver, using data from reference books and tracing the circuit myself, so I might have made (...) (22 years ago, 23-Dec-04, to lugnet.robotics.rcx, FTX)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR