To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *40774 (-10)
  Re: MERLIN valves & sensors
 
(...) But if you have a feedback system, the speed at which it activates is very important to avoid overshoot. Unfortunately the LEGO pneumatic switches do not make it easy to create feedback circuits, as they require a lot of force and have a (...) (22 years ago, 5-Sep-04, to lugnet.robotics)
 
  Re: OS-X driver for the Vision Command cam ?
 
(...) Yes! The Freeware open-source Macam works quite well. Details are at: (URL) a patched version for OS X 10.3 can be found at: (URL) (22 years ago, 5-Sep-04, to lugnet.robotics.vc)
 
  Re: MERLIN valves & sensors
 
(...) LEGO switches certainly aren't proportional - but I question the value of proportional pneumatic controls. The pressure either side of the valve will equalize very rapidly even if the control is opened only a small amount. Proportional valves (...) (22 years ago, 5-Sep-04, to lugnet.robotics)
 
  OS-X driver for the Vision Command cam ?
 
I think this has been asked before, but I don't see any positive replies... Has anyone hacked a Macintosh OS-X driver to support the VC LEGO-cam ? I believe someone has mentioned that the cam is really a Connectix QuickCam Web. I have found a linux (...) (22 years ago, 5-Sep-04, to lugnet.robotics.vc)
 
  Re: MERLIN valves & sensors
 
(...) Did you catch that these are *proportional* air valves? A LEGO mechanical air switch is not proportional, is it? (Genuine question -- I haven't gotten my hands on one yet, so I could be mistaken about that.) (...) Those are cool, but they only (...) (22 years ago, 5-Sep-04, to lugnet.robotics)
 
  Re: MERLIN valves & sensors
 
(...) I have not looked at the spec sheets, but the web page says 500 mA at 5 volts. The valve will probably draw 900 mA at 9 volts, which is past the current limit of an RCX motor port. Even without the current limit problem, you will have short (...) (22 years ago, 4-Sep-04, to lugnet.robotics)
 
  Re: best way to ignore sensors??
 
(...) This sounds like you have a sensor monitor running continuously, and there is code in the monitor. Perhaps if you set up the sensor monitor to only modify a variable rather than cause the RCX to do things, then your other code could monitor (...) (22 years ago, 3-Sep-04, to lugnet.robotics)
 
  Re: best way to ignore sensors??
 
(...) All right, if you're going to keep reposting your question until somebody answers... ;) Any other programming language will allow you to do that just fine. You write the code that makes the RCX do something in response to sensors; you can (...) (22 years ago, 3-Sep-04, to lugnet.robotics)
 
  best way to ignore sensors??
 
Hi. i am interested in programming my RCX to ignore one sensor port once another has been activated. I haven't found a way to do this with RIS Software so I wa wondering what other programming language would allow me to do this with the least amout (...) (22 years ago, 2-Sep-04, to lugnet.robotics)
 
  DCC for the RCX
 
Snippage If you haven't seen this check it out. DCC for the RCX (URL) (22 years ago, 2-Sep-04, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR