 | | Re: Control Cybermaster from RCX with feedback
|
|
(...) This might be old news, but I just tried it anyway... You can connect an RCX motor port to a CyberMaster sensor port and vice versa and get tri-state info. You can distinguish between the motor floating, off, and one of forward or reverse (...) (22 years ago, 11-Jun-04, to lugnet.robotics.cybermaster, lugnet.robotics.rcx)
|
| |
 | | Re: Control Cybermaster from RCX with feedback
|
|
(...) Yes, I also hoped for some ready made NQC library e.g., since I saw someone was working on that once (around 2001 in one of these newsgroups) Morten (22 years ago, 11-Jun-04, to lugnet.robotics.cybermaster, lugnet.robotics.rcx)
|
| |
 | | Re: Straight moving with only one rotation sensor
|
|
I did this in the past (since disassembled the bot) and found it to be quite reliable; except on slippery surfaces and carpet. :) The trick that I employed was to gear-up the rotation sensor. This causes the rotation sensor to detect even a slight (...) (22 years ago, 11-Jun-04, to lugnet.robotics.rcx.nqc)
|
| |
 | | P'titgneugneu the stairs climber, was Re: CC3:Stairs,
|
|
Here is the (URL) write-up> about the robot I built for CC3:Stairs contest, that happened to win ;o) A bit flimsy, not too pretty, but it did the job! (URL) As the results have not been published here, I inserted the official announcement below. (...) (22 years ago, 10-Jun-04, to lugnet.events, lugnet.robotics, lugnet.technic, lugnet.announce, FTX)
|
| |
 | | Re: Straight moving with only one rotation sensor
|
|
Have you come across the adder/subtractor drive? Although it make the gear chain slightly more complex - it may mean you can leave out the sensor entirely. The drive has two inputs (A and B), and two outputs - one being A+B, and the other A-B. So if (...) (22 years ago, 10-Jun-04, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Control Cybermaster from RCX with feedback
|
|
(...) It might be theoretically possible to use one RCX sensor port for control of the cybermaster - and using the one motor and one sensor port on the cybermaster. A few multiplexing designs I've seen use switching between passive and active sensor (...) (22 years ago, 10-Jun-04, to lugnet.robotics.cybermaster, lugnet.robotics.rcx)
|
| |
 | | Control Cybermaster from RCX with feedback
|
|
Is it possible to interface a cybermaster and an RCX without the use of a PC, also without using up all sensor and motor ports? Sincerely, Morten H Pedersen (22 years ago, 10-Jun-04, to lugnet.robotics.cybermaster, lugnet.robotics.rcx)
|
| |
 | | Re: Straight moving with only one rotation sensor
|
|
(...) Sounds good. I use a CyberMaster for the movement part of the robot because it has tachos on each internal motor. I modify the power settings for the motors to keep the robot (reasonably) straight, rather than stop and start them. If you tried (...) (22 years ago, 10-Jun-04, to lugnet.robotics.rcx.nqc)
|
| |
 | | Straight moving with only one rotation sensor
|
|
Hi I saw in the LEGO Mindstorms Web Page that many people made their robots with 2 motors go straight using one rotation sensor on each wheel and stopping the correct motor until both sensors were equal. I got Ultimate Accessory Set as a present (...) (22 years ago, 10-Jun-04, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: lego pneumatic
|
|
(...) Good reasearch..... Using the mindstorm motors, who's torque is a good match for the small pump, the small pump gets to a static pressure faster than a large pump using hte same kind of motor. The small pump does not keep up with the total (...) (22 years ago, 9-Jun-04, to lugnet.robotics.rcx.legos, lugnet.technic)
|