 | | Re: Control Cybermaster from RCX with feedback
|
|
(...) It might be theoretically possible to use one RCX sensor port for control of the cybermaster - and using the one motor and one sensor port on the cybermaster. A few multiplexing designs I've seen use switching between passive and active sensor (...) (22 years ago, 10-Jun-04, to lugnet.robotics.cybermaster, lugnet.robotics.rcx)
|
| |
 | | Control Cybermaster from RCX with feedback
|
|
Is it possible to interface a cybermaster and an RCX without the use of a PC, also without using up all sensor and motor ports? Sincerely, Morten H Pedersen (22 years ago, 10-Jun-04, to lugnet.robotics.cybermaster, lugnet.robotics.rcx)
|
| |
 | | Re: Straight moving with only one rotation sensor
|
|
(...) Sounds good. I use a CyberMaster for the movement part of the robot because it has tachos on each internal motor. I modify the power settings for the motors to keep the robot (reasonably) straight, rather than stop and start them. If you tried (...) (22 years ago, 10-Jun-04, to lugnet.robotics.rcx.nqc)
|
| |
 | | Straight moving with only one rotation sensor
|
|
Hi I saw in the LEGO Mindstorms Web Page that many people made their robots with 2 motors go straight using one rotation sensor on each wheel and stopping the correct motor until both sensors were equal. I got Ultimate Accessory Set as a present (...) (22 years ago, 10-Jun-04, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: lego pneumatic
|
|
(...) Good reasearch..... Using the mindstorm motors, who's torque is a good match for the small pump, the small pump gets to a static pressure faster than a large pump using hte same kind of motor. The small pump does not keep up with the total (...) (22 years ago, 9-Jun-04, to lugnet.robotics.rcx.legos, lugnet.technic)
|
| |
 | | RE: lego pneumatic
|
|
Hi , According to the (URL) a mini-compressor (using a single small pump) is actually more efficient than using double pump. It said more efficient, but not generate higher output though, correct??? (URL) produces a more persuasive test. However, (...) (22 years ago, 9-Jun-04, to lugnet.robotics.rcx.legos, lugnet.technic)
|
| |
 | | Barcodes for CodePilot
|
|
As I announced recently in another thread, I have modified the MicroScout transparency file from (URL) in order to print out all of the CodePilot barcodes on one letter sized sheet of paper. It can be found at (URL). I just thought I should mention (...) (22 years ago, 8-Jun-04, to lugnet.robotics.vll)
|
| |
 | | Re: lego pneumatic
|
|
(...) Interesting project. Will your car have a pneumatic engine? Pneumatic steering? The large pump can run the engine with no externally controlled switches. Steering on the other hand would require control of two switches. Both pistons expanded (...) (22 years ago, 8-Jun-04, to lugnet.robotics.rcx.legos, lugnet.technic)
|
| |
 | | Re: Spybotics playing tag - project
|
|
Steve Hassenplug schrieb: (...) I've made the spybot search and reach a lightsource with "SENSOR_2" :) And if you move the light - the bot will follow... Finding the spybot by IR is not exactly enough, thought. Now I want to make the lightsensor (...) (22 years ago, 8-Jun-04, to lugnet.robotics.spybotics)
|
| |
 | | Re: VLL Codes
|
|
(...) If you want to print out all the codes on one piece of letter sized paper, I have modified the file from (URL) to do so for the Codepilot. It is here (URL) in both Postscript and PDF format. (...) (22 years ago, 7-Jun-04, to lugnet.robotics)
|