 | | Re: Lego brick Database
|
|
"Jan Spies" <lego-robotics@crynwr.com> wrote in message news:000001c3a91d$ac...@hgfdhg... (...) (URL) (22 years ago, 12-Nov-03, to lugnet.robotics)
|
| |
| | Lego brick Database
|
|
Hi Does anyone know of a stock system which I can use to keep track of my lego bricks? JanS ---...--- Technikon Pretoria ---...--- This email is sent and received in terms of the Electronic Communications Policy of Technikon Pretoria. In line with (...) (22 years ago, 12-Nov-03, to lugnet.robotics)
|
| |
| | Re: polish version of mlcad
|
|
DL (URL) (22 years ago, 12-Nov-03, to lugnet.cad.mlcad, lugnet.robotics, lugnet.technic)
|
| |
| | Re: Help w/install _or_ It all went so well
|
|
(...) [...] (...) Well it looks like the gcc-version-problem I had. The gcc >=3.x do not allow multiline strins without "\" anymore, which are still uses in brickos. So my hint is to install a gcc 2.95 and everything should work fine... Note: This (...) (22 years ago, 12-Nov-03, to lugnet.robotics.rcx.legos)
|
| |
| | Help w/install _or_ It all went so well
|
|
_warning_ I'm new to BrickOS, so be patient. I've just attempted to install using the instructions at (URL) went fine until step 4 command './configure; make' which looked like this: ... $ ./configure; make Welcome to the brickOS Makefile (...) (22 years ago, 12-Nov-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: I'm passing the NQC torch...
|
|
Dear Dave, All I can Say is Thanks. But that says it all. JL (22 years ago, 11-Nov-03, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: ROM image using USB tower
|
|
(...) Andrew, I grabbed a ROM image awhile back using a serial tower and an RCX 1.0. I haven't tried this on a 2.0 brick, but I think the ROMware is identical in all RCX versions. Although Kekoa's SEND.C uses the serial tower, it is not too hard to (...) (22 years ago, 12-Nov-03, to lugnet.robotics.rcx)
|
| |
| | Re: Alternate IR Comm Setups
|
|
(...) Dustin, I believe that the built-in IR in a laptop uses a different carrier frequency than the 38KHz used by the RCX 1.0. I've seen reports here that the 2.0 RCX can be reconfigured (with some low-level system programming) to use a 76KHz (...) (22 years ago, 12-Nov-03, to lugnet.robotics)
|
| |
| | Re: I'm passing the NQC torch...
|
|
(...) Dave, please allow me to add my name to the list of appreciative fans of your work, and the generous example you put forward to the LEGO/Mindstorms community. We all owe you a lot! -- Russ (22 years ago, 11-Nov-03, to lugnet.robotics.rcx.nqc)
|
| |
| | ROM image using USB tower
|
|
Hi, I'm doing a project at University involving developing some example programs running on a Lego RCX in order to demonstrate/teach OS concepts. I'd really like to get hold of a ROM image from the RCX, but I only have a USB tower available, and (...) (22 years ago, 12-Nov-03, to lugnet.robotics.rcx)
|
| |
| | Alternate IR Comm Setups
|
|
Has anyone attempted or had any success using the built-in IR ports on laptops to communicate with the RCX? Dustin (22 years ago, 12-Nov-03, to lugnet.robotics)
|
| |
| | Re: I'm passing the NQC torch...
|
|
(...) Please allow me add my sincere thanks to Dave for all the hard work he has put in over the last few years. As far as I am concerned, RIS only really appeals to me because of the access that NQC has permitted to the RCX. Were we to have been (...) (22 years ago, 11-Nov-03, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Homebrew sensors (where to find them)
|
|
(...) I have used Pete's stuff. (URL) (22 years ago, 11-Nov-03, to lugnet.robotics)
|
| |
| | Re: I'm passing the NQC torch...
|
|
(...) Dave, Thanks so much for the work you have put into NQC. I have used this tool exclusively with BricxCC. You have changed the face of Mindstorms programming and for that I and I am sure many others are grateful. Thanks again, Dave (22 years ago, 11-Nov-03, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: I'm passing the NQC torch...
|
|
(...) I too just wanted to say a huge THANK YOU for your hard efforts. Even them small changes you made for me to make it work better with my setup. I can honestly say that with our NQC the VLC's automation layouts would not have been possible. Your (...) (22 years ago, 11-Nov-03, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: I'm passing the NQC torch...
|
|
(...) ...and it's consequences were beyond imagination. Thank you, for taking an interesting "toy" and opening up the world for the rest of us. (22 years ago, 11-Nov-03, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: I'm passing the NQC torch...
|
|
(...) Your contribution to the Mindstorms community through NQC has been fantastic. When I started with Mindstorms, that was the only language I used for a long time. Thanks and the very best regards !! KK (22 years ago, 11-Nov-03, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Memory Map for the RCX
|
|
(...) Here's a brief summary: 0000-3FFF On-chip ROM 4000-7FFF Unused 8000-EFFF External RAM F000-FB7F External RAM, motor control register (write) FB80-FD7F Reserved FD80-FEFF On-chip RAM FF00-FF7F On-chip RAM (can use 8-bit addressing modes) (...) (22 years ago, 11-Nov-03, to lugnet.robotics)
|
| |
| | Re: I'm passing the NQC torch...
|
|
Thank you Mr.Baum. you have brought great help to the Mindstorms community. I read somewhere that you live in Lake Zurich. I also live there. i hope you continue to contribute. Once again, thanks. -Nick (22 years ago, 11-Nov-03, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Mars Rover
|
|
We also had low battery ... on MARS! We beamed one human being to replace them. Then we had the firmware lost. This was a job only for Scotty. Now all seems to work again for three quarters of an hour. Then everything will be shut down until (...) (22 years ago, 11-Nov-03, to lugnet.robotics)
|
