 | | Re: Beta Tester(s) wanted NQCSpeechCompiler
|
|
hi Dean, ever heard of "Dasher", could be an alternative too ? Stef (...) (23 years ago, 24-Oct-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Snaptrax remote control vs other Spybotics remotes control
|
|
"David Koudys" <dkoudys@redeemer.on.ca> wrote in message news:H4HLMq.B5E@lugnet.com... (...) ;) ). (...) after (...) and (...) To get it to transmit on all channels again you must hit that forth button. Then it resets it back to all channels... (...) (23 years ago, 25-Oct-02, to lugnet.robotics.spybotics)
|
| |
| | New Syngress RIS 2.0 Book!
|
|
Syngress has published another LEGO book, continuing the series started by the Dark Side Developer's Kit book, and to be finished up by the Ultimate Builder's Set book. I think all three will be available in a kit too. This current book is specific (...) (23 years ago, 24-Oct-02, to lugnet.announce, lugnet.books, lugnet.robotics, lugnet.technic) !
|
| |
| | Re: h8300-hms-ld segmentation fault under WinXP
|
|
"Joseph Woolley" <jwoolley@spamblock....ht.rr.com> wrote in message news:H4HvF3.C03@lugnet.com... (...) Win2k. (...) Ah, so it's not just me. I've been tearing my hair out trying to figure out what I might be doing wrong. A few years ago I had (...) (23 years ago, 24-Oct-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: h8300-hms-ld segmentation fault under WinXP
|
|
I don't think the problem is WinXP specific: I had the same issue on Win2k. I ended up using the prebuilt gcc/binutils from hitachi for that reason. However, the prebuilt set is quite a bit older. I hope this issue can be worked out so we can begin (...) (23 years ago, 24-Oct-02, to lugnet.robotics.rcx.legos)
|
| |
| | h8300-hms-ld segmentation fault under WinXP
|
|
Hello, Are there any know problems getting the h8 cross compiler working under Windows XP? I'm using the latest cygwin environment, along with gcc3.2, newlib1.10, and have tried both the binutils source distributed with cygwin (2002070601?) and I (...) (23 years ago, 24-Oct-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Snaptrax remote control vs other Spybotics remotes control
|
|
(...) From my experience, The remotes, when first turned on, seem to send out the signals on all channels (1,2,3), until a specific channel is picked--then the remote only works for the robot that is on that specific channel. This happened with the (...) (23 years ago, 24-Oct-02, to lugnet.robotics.spybotics)
|
| |
| | Re: Battery drain just to run a program?
|
|
(...) I think a switched on RCX that doesn't use sensors or motors draws ca 10mA, regardless of the program running. That's enough to drain batteries in a few days. Jürgen (23 years ago, 24-Oct-02, to lugnet.robotics)
|
| |
| | Snaptrax remote control vs other Spybotics remotes control
|
|
Did you noticed that Snaptrax remote control can directly control any Spybotic, as others remotes can't ??? I'm wondering why... - Christophe - (23 years ago, 24-Oct-02, to lugnet.robotics.spybotics)
|
| |
| | Re: Battery drain just to run a program?
|
|
(...) Yes - most ultra-low power devices actually shut down most of the CPU circuitry for most of the time...just waking up when something interesting happens. Your CPU was running at full speed the whole time. Imagine something like a GameBoy (...) (23 years ago, 23-Oct-02, to lugnet.robotics)
|
